Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
New to the WLC Configuration but have configured Cisco ASA and Cisco standalone AP in the past. Trying to get this configured up following 2 videos... Cisco WLC2106 Initial Configuration How to https://www.youtube.com/watch?v=O3CDIsSXU0s WLC2106 ...
Hi All, Its been noticed the PrimeInfra is not showing the correct clients information from WLC when doing a live thsoot. Has anyone noticed this issue before and is there any fix for it ? Thanks
Hi All, I currently have a network consisting of a WLC5500 controller and 3850 core switch which has mDNS gateway running and working fine across VLANs. The customer has now asked if we can deploy this as two sets services - i.e bonjour services fr...
Hi Team, MSE is showing unreachable status showing on prime , Version is : 8.0.130.0. Please assist on the case. Thanks..
Hi folks, I need to do cod upgrade and FUS upgrade to my WLC Do we need to preload the FUS to the APs similar to what we do with the code ? Or FUS doesn't need to be downloaded to APs
i have dhcp pool AC configure on Cisco 3750 where i already have 10.85.49.0/24 series but i want to add one more series because the 10.85.49.0 series is exhausted so i want to add 10.85.93.128/25 series in same pool so WiFi user can also get ip fro...
previously 802.11ac requires WMM and wpa2/aes psk for the client to achieve optimum performance. so what happens when we use NAC/802.1x and leave off the PSK?
Hello I mistakenly deleted from the web interface the filter "702" of the mac addresses wich are allowed to connect to an access point aironet 1130ag, is there a method to recovery it and have it in the interface web, the access point still allows th...
Hi everyone, We have a WLC 5508. A few days ago, we upgraded software version from 8.0.120.0 to 8.2.151.0. After that, the connection was slow (<1Mbps for b/g/n devices and good with ac devices) I searched some documents and support topics but I go...
Hello people! I´m new in this kind of CLI configurations because I´m not goint to use WLC. I´ve attached the desire architecture. The APs that i´m going to use are Aironet 1552S. Please if any one of you knows the command lines to configure the APs...
Hi all, I have (2) 1852i access points. #1 accepts Mobility Express Upgrades fine, now running 8.5.105.0 and is up and running as my controller. #2 is running 8.2.100.0 and will see the controller, controller accepts, then it fails the image downlo...
Hi all. Does the Cisco AIR-AP1252AG-N-K9 running IOS Release 15.2.2-JA1 support IPv6?
Hello,I have used 2 Meraki MR66 and some months ago I have this message "This network has been disabled" from the site https://n30.network-auth.com.The wifi connections shows that I'm connected to the wifi network but i cannot acces any website, and ...
Hi allSince 2 weeks we have 10 8821 Cisco IP Phones in use. On every Phones we have a poor Battery Standby Time. According the Data sheet we should have a Standby Time about 200 hours. The Battery on our Phones is over one night empty. System we run:...
I'm looking for suggestions on the software I should use to create wireless maps, I know it can be done in Autocad but I was looking for something a little easier and less expensive to use. What would you recommend to draw our wireless maps? Than...
