Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi Cisco Gurus, I am just getting crazy trying to move a Campus I created on "Site Maps" from the Unassigned Campus. I would like to put it just below the root. I already tried to remove it and create it back from scratch, but when I create an outdo...
AIR-CAP1602E-A-K9 gets ip address but cannot be seen on WLC. I used debug mac addr, debug capwapp events enable, errors enable. (Please see attachment). AP is blinking from amber, green and red. Ping on the AP is ok and then it will timeout for some ...
I need to connect two warehouses wirelessly but do not know which antenna to take.The distance between the two warehouses is about 30 meters, the warehouse B is 30 meters long by 15 meters, and I want to understand what I need. I have all the equipme...
Hi there,I'm facing a bit challenging problem. When I boot one accesspoint it gives only next listing in the screen:Xmodem file system is available.Flashfs[0]: unable to allocate available block.The system has been interrupted, or encountered an erro...
in a 1242 LWAPP, what does"Environment variable (ENVAR) failure" indicate?
Resolved! Cisco enterprise wifi, WLC or Meraki
Hi All We are looking out swaping our Aruba wifi with Cisco controller based, we use Cisco wifi on most of our global sites so want to aim for a standard. We currently have around 300 ap's around a few sites that connect to 2 controllers. Firstly can...
Hello, Please i need help about the following issue: I upgraded Aironet air-lap1142n-a-k9 from autonomous to lightweight in order to join a 2504 WLC. The firmware i installed on AP is c1140-k9w8-tar.153-3.JC and on WLC the software system is 8.1.102....
HiI need to backup an AP IOS to a TFTP server, I use the archive tar /create command according to the cisco documentation and I get an errorap#archive tar /create tftp:192.168.1.186/c1200-k9w7-mx.122-11.JA3.tar flash:/c1200-k9w7-mx.122-11.JA3%Error ...
Hi for access points not supporting ELM, and only operating in normal local mode with no submode, does the access point also go off-channel scanning and detects threats etc.. ? what is the difference between an access point operating in normal Loc...
I recently upgraded our Flex 7500 WLC to software version 8.1.131.0 for the requirement to be able to configure Anchor controller redundancy. Now I can see on this version of code, you can set an anchor controller priority to 1-3 (1 being the highest...
Hi Everyone, Looking for some suggestions or feedback on how to implement what I'd call a mobile wireless bridge. In our manufacturing environment we have a "mobile crane" that needs a bridge from our wireless access points into the mobile crane. T...
Hi, We have setup a 3 Lightweight AP using WLC 2500. We've created a Guest SSID with local web authentication. Session Timeout was disabled and User Idle Timeout is set to 86400 (24 hrs). Our main problem is that, Apple devices such as MAC book, Ipa...
Hi , please help me to configure wireless ssid so that this 1. ssid will give wireless access to user connected to that SSID , this new ssid user should not get access to enterprise LAN. 2. After connecting to SSID , they will get access to internet ...
does client transition happen seamlessly in WLC/3850 MC/MA deployment when client moves from AP connected to one 3850 MA to another AP that's connected to different 3850 MA? if yes then how does the traffic flows? does client retain same IP address o...
Resolved! Wireless QOS
2504 controller running 8.0.120.0 On the QOS profile for platinum, when I am trying to select wired QOS protocol type to 802.1P, the conversion value I get is 5 (earlier code it was 6). Questions : My understanding earlier was since 802.11e mapping o...
