Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
in switch, I have one interface G1/0/35, type: trunk, connected to access point 2, in switch G1/0/35, can we list out the IP address of AP 2? how would I know the IP adress of AP under my switch under g1/0/35, currently, there are three mac address ...
Hi,I have a stack consisting of 2 WS-C3650-24PS (version 03.03 .05SE) configured as MC and 4 AIR-CAP3702I-E-K9.Everything is working properly and the APs are joined without problems, but only if the port of the 3650 is configured in access mode. This...
We got six 2960x switches (48-port) deployed this summer in our school and I have all our 3702i APs connected to them and they are powered by the PoE from the switches. But that will downgrade the APs to 3x3:3 mode. Our IT consultant told me that "yo...
Hi,I have purchased new Access point 3700 series (air-cap3702i-e-k9), please kindly guide me to configure. I have try to get global config mode but I can't get it. bestChandra
Hi All, I have a client replacing their existing WiFi with a Cisco solution. They currently have a guest SSID with a PSK and have an external proxy presenting an AUP disclaimer page that they have to accept before proceeding - they initially want to ...
Hello ! I'm looking for advice in this matter. We have one virtual WLC with base-ap-count license for 40 APs (we bought L-LIC-CTVM-UPG and 7 x L-LIC-CTVM-5A), but we are using only 18 APs.We are going to buy another one WLC for remote office and want...
Hello All, We are currently having 100 AP licenses on WL-C5508. We want to increase our licenses to 150 by adding 50 capacity adder licenses. I am going to follow below steps to do so. Can anyone please verify and let me know in case i am missing som...
I'm in a situation where I would like to plug another standalone AP into the AUX port on another standalone 2702. No controller is used. I'm wondering if this can be done, or if it will work. I can will have power adapters for both. I'm going to ...
Can someone give me concrete reasons why we should NOT enable broadcast forwarding to resolve the issues as described below? We have roughly 85 - 2504 WLCs all running 8.0.120 code scattered across 85 physical sites. We have an issue that I have fi...
Hi,Is there a way to select with what controller can an AP register ? I have 40APs and 2 controllers and I want to be able to choose with what controllers an AP will register based on MAC Address?Thank you!
Hi there we just upgraded our Cisco WLC 5760 from IOS XE 03.03.03 to IOS XE 03.06.03 and every thing seems to be working fine, except that we get a lot of the following error messages:Sep 24 13:00:10: [CAPWAP] %Error: fast_ipwrite returned 2. Try ipw...
Hi, trying to get an AP to register with the controller, but it aint happening. I was reading an old post:https://supportforums.cisco.com/discussion/12503981/cisco-air-ap3702i-uxk9-flashing-redgreenoff-registered-wlcand it mentions that the AP is un-...
Need a in between solution for APs..need to find out the CISCO AP model that support standalone mode (autonomous mode) for now. AND these AP will convert to lightweight (with WLC) at later time.The current new 3700, 2700 and 1700 seems all use WLC.. ...
hello everyone, we have a problem with the ip mapping on connection of ISE and WLC. this is how is our network:vWLC: 8.1.111.0 IP:172.16.100.14 ; virtual Ise: 1.0.3.876 IP:172.16.100.17Both are on the same virtualization server.The users...
Dear all, We plan to install on the same site these devices :- AIR-CT2504-50-K9 – as primary controller- AIR-CT2504-HA-K9 – as backup controller- Software version 7.6.130 I didn't find documentation on how to make the HA between the devices.The two d...
