Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello everybody.I'm noticing two of my 30+ APs having the 802.11a radio with "Operational Status = DOWN". The Admin Status is ENABLED, but I don't know where to act to put the op. stat. UP!WLC is running 7.5.102.0, as well as the APs. The affected on...
I just put in a 5508 WLC with a pretty basic setup. I have a Guest WLAN configured that uses authentication with the local user database on the controller. When I connect to the wireless network, I get an IP address from DHCP and my wireless adapter ...
Hi all, I have recently upgraded my controllers from WLC 4404's to some 5508's. We had multicasting configured on the previous controllers for our IPTV solution. Now that we have upgraded to the new WLC's this has stopped working over the wireless. T...
Hi,End user has a WLC 5508 and around 12 LAPs (an increasing un short time) configured and working for mesh network (some ROOTs and MAPs)now is the way to deploy an additional 5508 in another site so that be the backup of the first controller. Tak...
Hi, What is the method to verify what ssid is a mobility anchor group using? We have a mobility tunnel whose one end wlc(5508) will be changed shortly, which will need some changes on the tunnel I believe. Before this is done, we will need to do so...
Hi, I am facing an issue with my AP not joining the controller. Following is the error log Mar 1 00:01:11.923: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER*Mar 1 00:01:21.923: %CAPWAP-3-ERRORLOG: Go join a capwap controller *Apr 3...
Resolved! 7.6 WLC and per user ACL for flexconnect
Hi All,Im in the process of configuring our new 5508 WLC running version 7.6 code with 3700 APs.We run ISE, and have setup our IT Admins to run on a separate VLAN on the wired from general users which works good. This allows us to control who can acc...
We have WCS running on a VM, and due to some issues with the VM Infrastructure everything shut down abruptly. The VM came back OK, but I just noticed that WCS no longer loads properly when attempting to access it via a browser. Checking out the ser...
hi All, I have a AIR-LAP1231G in the network which is associated with a WLC running 7.0.235 firmware. We are planning to shut this controller. The new controller in site is 5508 with 7.4.110 firmware, would like to know whether my LAP can work with t...
I configured my Aironet 1262N autonomous AP to authenticate and account my users against a FreeRADIUS server. In the RADIUS server database, I saw some records like:select username, acctauthentic, acctterminatecause, acctstarttime, acctstoptime from ...
like the title, i have upgrade the wlc version to 7.4.121.0,but the question didnot resolve.
I am copying IOS file to 3850 Using TFTP and it is taking long time and i tried with different TFTP servers and different operating systems.
Hello.I am trying to configure cisco 3602E access point. And I currently have two choices: local mode or local + wips. Do I realy need wips? I have also cisco 3850 WLC. Thanks.
Recently, i migrated some 350 AP from WiSM-1 to cisco 5508 controller with 7.6.100.0 code version. We have 300 nortel wireless phones that was working on old WiSM, now we are not able to hear anything and the calls always disconnecting. Any help appr...
Resolved! Device Type "Unkown"
All, I am in the process of configuring a new 5508 WLC and five 3702I APs. Looking at the Client Monitoring page I can see all the client associated with the APs but The Device Type says “Unknown.” Is there anything that can be done to change/resol...
