Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I am looking at installing WLAN to one of our outbuildings at work. I will be putting the transmitter/receiver on building roofs but due to traffic passing the link may lose line-of-sight for short durations (5-10 seconds).Would this adversely affect...
Hello Sir, I want know from A to Z the details regarding planning and implementing wireless solution and technologies in power plant controls. (I will install a WLAN in a power plant). I want know all the different wireless technologies with all the ...
I created a wlan on my Cisco 8510 controller for guest users and I would just like for them to get acceptable use terms and then click accept or reject. The users get the default page when it is selected. I uploaded the login.tar from the webauth b...
Hi All,I have two question, We have upgraded all our 4 x 5508 WLCs from 7.4.110.0 to 7.6.130.0 afew weeks ago.1. We have BOYD Wifi where we have two WLC are front end (where the APs join) and two in the DMZ are anchors.On our BOYD Wifi its WPA+WPS2...
Hi Experts ,We want to establish HA between two 5760 WLC's. These controllers will be there in seperate building . So IS there anyway that we can establish HA without using stacking cables?
Tenho 2 Access Point CAP2602I-T-K9.Configuramos o AP1 como RootAP e o AP2 como MeshAP (sem cabo de rede).Porém, o AP2 não está aparecendo na Controller?O que tenho que mudar nas configurações?Obrigado,EveraldoUNIFEI
For economical reasons i want to see if it is possible to use two AP350 instead of to 350 bridges to bridge a LAN, is it possible?
Hi,Does anyone know if it's possible to use a WLC2504 as a guest anchor when we have deployed 3850's for regular corporate WLAN?The corporate stuff is all up and running OK using 3850's but i've now to come to look at the guest provisioning and i'd l...
Please can someone can help me configuring Cisco 887 VAG - 4G router to enable internet through 4G (Sim Card) Any help / advise will be appreciated. Kind regardsAB
Hi, Can anybody please clarify.I have configured the APs domain/nameserver details (1602i's and 1042n's) from a WLC (8500 series, through command not through the browser) and the APs successfully take the config. I've checked this by telnetting into ...
I have up to seven notebook users connecting to the Wlan via an AP350 base station. The throughput has slowed as more users make use of the wireless network. How can I improve the Throughput?1. More Stations (we have 2 now)2. Bigger antenna.3. Someth...
If I apply the Demo license to a licensed Prime Infrastructure server will it enable all the features so I can test the Netflow features for the demo period? I have never used the Netflow features and would like to test drive for a little and decide...
We recently put into production a number of 7925G phones with Plantronics H171N head sets. Half of our users have reported not being able to hear other party and vice versa with Plantronics head set. Sometimes, when they reconnect the headset into au...
I have two 5508 wireless controller with license of 50 APs. But we have 70 Aps and we want to use those controllers in redundnat mode. but the problem is after redundancy configuration it becomes 1 unit and support only 50 APs. How can i use two 50 A...
Hello, Do you have any idea about the (max) length of the MTU supported by the C819HG-4G-G-K9 on the air intterface? the antenna 3G-ANTM-OUT-OM can operate on the frequency range 2100-2200 MHz? thank you for your help
