Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
What is the maximum acceptable CPU Utilization percentage for a CISCO MWR 2941-DC router that is not prone to errors?
Hi,I noticed that the wireless networks in my building are broadcasting further than I would like e.g. They are broadcasting into the buildings across the road from my building.I have Cisco wireless controllers/APs and Prime infrastructure installed ...
Hi,yesterday ive got my WAP561. I fidured out that he is not able to establish a Network Connection to my Netgear POE Switch (GS110TP). The Port stays down. So i tryed it with an POE Injector and an HP1810G Switch. Again no Link. Wenn i attach the Li...
Hi All, Just looking at AP configuration using 5508 WLC. We have APs deployed at all branch sites connected over a corporate L3 WAN to a Data Centre which houses the WLC(s)When setting the AP for Flexconnect mode there is a requirement that one nativ...
HElloi am trying to setup ISE 1.2 to be radius authentication server for our WLC admins; we have thsi setup for older WLCs no problem but with this new WLC it just not working. Any good document i can follw to setup admin access via radius ISE 1.2? t...
Hi all,I am trying to build a Ethernet bridge. The bridge does form ie RAP -> Mesh.If I connect wireless to Mesh I have communications.When I connect the Mesh to a switch (trucked on switch & RAP / Mesh) and connect my Ethernet to the switch I don't...
We have deployed many Cisco site specific WLAN controllers worldwide.We are now testing APs in Flexconnect mode at our branches with regional C8510 controllers running 7.6.110.0. One of the issues that we see is that if we deploy a new AP and get it ...
I read that one must use the user/pass method of web auth to take advantage of the newer "sleeping client" functionality. Certainly the same need for this function applies to Passthrough (acceptable use page submission) authentication as well, since...
Hello, is there somewhere a documment that describes something like supposed distance which the wireless signal can reach when using for example AIR-ANT2566P4W-R? I need to know if I can use this antenna together with 2600 AP to create a point to po...
Hello,i have a 5508 HA cluster with different software.Primary AIR-CT5500-K9-7-6-110-0.aesSecondary AIR-CT5500-LDPE-K9-7-6-110-0.aes and a 6.x FUSis it possible to change the secondary to AIR-CT5500-K9-7-6-110-0.aes and FUS 1.9.0.0 ?Rega...
I have many sites all in Flexconnect, controller by 8510 controller, is it possible for GUEST to do central data switching.I know authentication can be done centrally.Thank you
I'm planning to extend our WLAN for outdoor environment. due to the limited budget, I considering use some 2600e AP (mesh IOS) to achieve this goal.As we know, MESH using 5G for backhaul and 2.4G for client access. So it is possible to using a direc...
Hi All Hope all are doing well I have vMware EXi.3.5 i want install Cisco vWLC in exi.3.5 Just want know Cisco vWLC it support vMware EXI 3.5 version ?????? Please help me Regards Muhammed
Hi,Anyone tried the new 2702i/e access point?Is this an replacement for the 2602-series? with an upgrade to 802.11ac?Does anyone know if this AP is supported for the WLC release 7.6.100? //Jan-Erik
I have two 8510 wireless controllers connecting to each other via the redundancy port, one WLC is the active controller and the 2nd WLC is the standby controller. Each WLC connects to a pair of Nexus 9708 distribution/router using Port1 and Port2. I ...
