Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
helloI want to know if it is possible to change the authentication key on a secondary NCS.is is setup at the beginning of the installation.But you also use this key to login ( Web login) to the secondary appliance.ReagrdsMichel M...
hi all,we have two wlc controller (192.,168.10.5 and 192.168.10.10). I have set a dns entry for Cisco-LWAPP-Controller to join 192.168.10.5 and Cisco - CAPWAP-Controller to join 192.168.10.5. we run cisco switches for dhcp and i have given option 43...
Hi AllI am having an issue with a particular Vlan and SSID. I have an several access points that are autonomous and talks to a controller.There have been no issues or changes made on the wireless controller. A few days a go the wireless connection to...
Resolved! Access Point support on WiSM 2
I think I already know the answer, but I cannot find any solid documentation. Does the WiSM2 support the 1231G AP, if so can anyone provide documentation?Thanks.
Resolved! Guest Wireless access over WAN
Hello Everyone,We have around 45 remote location , all are connected with GRE Tunnels.44 location have there own WLC which are managed by NCS and ISE in HQ , All 44 location have Wireless access for Guest and INternal Staff.Now my Question is :One lo...
I'm trying to set up tacacs+ to our Cisco Prime Infrastructure 1.2. Currently we use ACS for this, but we're moving to radiator.It logs you in, but then says 'you don't have access to overview' and basically you get no access at all.I have a feeling ...
Resolved! Cisco 2602 AP
Dear All,We have just purchased some Cisco AP 2602 , but there is no POWER_CABLE / POWER-ADAPTER with the Access-Point devices. Any Idea, Why Cisco has not included it ?
Hello There is a problem with Cisco AIR-MSE-3310-K9.Has failed one of the hard drives. After replacing it, raid status changed to "Rebuild".It was reported that the replication will be executed automatically when the system boots. After the system bo...
I have two Cisco 1200AP.I have it configured with two SSIDs, one corporate (802.1x) one using WPA2 Personal.I have no issues on the corporate, but I have found that Apple devices appear to detect it as a WPA2 Enterprise, and request a username and pa...
I am running 1252 APs with 802.3af power and HT/11n disabled so it seems to work OK. However, when I configure minumum RF power to 2 dBm in the RRM settings, the radio should be set to RF Power Level 7 by RRM. It is actually set to Power Level 8.In...
Hello,it seams, that the mounting blade for the 1142 access point and the 2602 access point are identical. Can this anybody confirm?We have ordered the new 2602 with internal antennas for deploying WLAN in a new building, but I never hold this access...
Hi,I have a small outdoor mesh implementation in an airport. I have this problem that the A-radio of the RAP goes down and getsdisabled and can't be enabled. I see in the logs "Radar signal detected on channel xx". How can I solve this kind of pro...
I have several 2602 AP's that I want to operate in FlexConnect mode. The WLC is at a central HQ and the Ap's are remote. There are central radius servers at the HQ for the wlans. At the remote lcoation, there is a local radius server we want to us...
HiWe installed 20 access point (1310 LAP) in 4 km tunnel ( each 200 meter one ap) for vowlan projects with 7925g phones .on each radio we have 2 antenna (AIR-ANT2506) and diversity is enabled .But we have problems like one way talks or weak signal ....
1. Topologywism(ver 7.0.98) <-> ap <-> pdaBelow is a message log of WiSMWhat's means this message?*apfMsConnTask_0: Jun 07 13:55:41.035: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2206 Could not process the RSN and WARP IEs. error processing RSN IE....
