Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! WLC2112 shows 6 APs only
Hi Guys,Recently I purchased AIR-WLC2112-K9, but when I logged in I saw that system shows only 6 APs supported (I made print screen in addition).I'm running IOS v. 7.0.116.0 and I saw that there was some problems with earlier versions of IOS, but not...
Resolved! TPC Power Transalations
With the newest version of code on the controller, I have seem to lost the power translation levels for the Transmit Power. We typically try to set the APs on controllers we deal to go no lower than 50%, Power Level 4. On the old 6.x version of code ...
Resolved! AP-Manager Interface on WiSM2
I know the WiSM 2 is like the 5500 WLC regarding the fact that you do not need to configure an ap-manager interface for CAPWAP packets because by default the managment interface acts like an ap-manager interface.What is best practices? Any major adv...
Hello,I have three WAP4410N WAPs that I need to set up in our office so that where ever you move throughout the office, you stay on the same SSID seamlessly. The WAPs each have their own POE connection back to a wired router with Internet access. Nat...
I have a WLC 5508 on the 6.0 code. I am running PEAP. Users login with the certificate staged and are coming up with 169.254 addresses. From the controller however, I see them at valid address from the virtual interface I expect (10.1.27.x). On m...
Hi, I'm setting up a Guest WLAN using the passthrough WebAuth option. All the configuraiton works fine, but I'd like to change the Cisco page that says "Welcome to the Cisco wireless network....". None of the documentation that I have read tells me...
Here is an output from our Aruba Airwave server. I've been trying to reduce the constant radio utilization on some of our APs. I succesfully did it by disabling the 1 and 2Mb data rates on the APs. However, for some reason the FCS errors have gone up...
I have 55xx WLCI have 100 API want to limit higher "DATA RATES" for certain APs, how?I see it is possible to do it for all a/n or b/g/n radiosPlease Help
Hi, I have WCS in version 7.0 My task:The space is running out on C:, I want to start logging in to HDD D:, where I can change this settings ?
Hitoday i upgraded our WLC4402 from 7.0.98.0 to 7.0.116.0. After the upgrade (also bootloader upgrade) the Aironet 1142 AP's do not joint the controller anymore. Error in log:*spamReceiveTask: Apr 26 11:30:46.301: %CAPWAP-3-DISC_INTF_ERR2: capwap_ac_...
Hi,We have a Cisco 4400 controller and a mix of 1010 and 1131 access points.We have been running out of IP's on our DHCP server because the apple devices are not releasing there IP's.If you have experienced the same problem, could you let me know how...
Only getting 9-10MB of throughput on the Cisco OfficeExtend AP600's. I have a 25mb pipe, and when I use another router, and even a Linksys I'm able to get 25MB downloads. Let me also clarify that I'm using the personal / local SSID of the OfficeExten...
We have a 2100 controller with 4 wireless AP's, only one connected directly to the controller. I want to use the controller for the DHCP server for Guest, thermostats, in house wireless networks on this system. I cannot seem to get the DHCP setup pro...
Hello all,I am trying to convert an 1142 from lightweight to autonomous. I've found this post:https://supportforums.cisco.com/thread/2055997However the following command is not available via the CLI: archive download-sw /overwrite tftp:// Any though...
Any ideas how to make the Ascom work with the latest IOS with the Ascom using a static ip? Works fine on older IOS but not the new one. Thanks in advance.
