Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Wireless AP Bridge commands
In every sample of configuring wireless access points, including Cisco documentation (notably the older Aeronet ones), I find the following lines to be configured on the bridge group which includes the radio interface: bridge-group 1 block-unknown-s...
I am new to configuring these 9800 controllers. I have experience with a 5200 series controller and I am aware that the firmware is different. I am in an ongoing battle with DHCP working but not as intended or not working. I am trying to configure th...
Resolved! 9800 HA N+1 Retaining AP Tags
We are in the process of converting to Cisco 9800 controllers and are testing the HA failover in a N+1 deployment. When AP's are failed mover to the secondary HA controller, they are falling into the default policy, site, and rf tag group. On the H...
I've noticed some odd behaviour for web auth ("global" parameter map). This applies on IOS XE 17.9.3 and 17.9.4a, and possibly on other versions too.If I use the web GUI to define the banner text as "Welcome", then save my changes, this gets truncate...
In some release notes for APSP it states that for example SP2 contains all the fixes of SP1, so you only have to install SP2. But I cant quite seem to find this "wording" on APSP release notes for 17.9.4. Did it change ?
Resolved! client exclusion of WLC
Hi I would like to ask that is wireless client MAC address has been assgin to Excluded Clients, does the WLC will ignore the "auth request" during the exclustion period? Frankie
Resolved! about CAPWAP data flow
As I know, a WLC receives a user packet from AP via CAPWAP, it will remove CAPWAP header, translate L2 header and forward it to a GW. Here are my questions and do appreciate any input from you. Thanks!Q1. If a WLC uses trunk port to connect to L3 sw...
Deal All,I had recently set an 3802 AP as a Monitor AP to troubleshooting signal issues.I can ping the monitor AP but could not webpage to it to check the logs it capture.is there any alternative to check out the logs ? from the 5508 WLC ?Any help ar...
I'm trying to upload new software to scces ponita. After running the update, an error appears.ap-type mobility-express tftp://10.10.100.20/AIR-AP2800-K9-ME-8-10-190-0.tarImage transfer complete.Image downloaded, writing to flash...do CHECK_ME, part1 ...
Hello,C9120AXI-B APs are joined to WLC 9800-L with US country code.I tried to join several APs AP3802I-E-K9 with UK country code to WLC 9800-L. But failed. Reason is Regulatory domain check failed.When
Hi All, I am tying to get my new AP AIR-AP1562I-E-K9 installed in our airport and its mounted and learning in switch CDP neighbor but its not getting registered in WLC switchname#sh cdp nei Gi1/0/48 det-------------------------Device ID: AP3473.2DA2....
While trying to transfer AIR-CT3504-K9-8-10-183-0.aes to Cicso AIR-CT3504-K9 WLC controller, it shows below version mismatch error.Current boot image for 3504 WLC is running 8.5.140.0 ==============================FTP Code transfer starting.FTP rece...
We have recently deployed a wireless guest CWA solution that involves 9800 WLCs, ISE and Checkpoint firewalls. Our topology isGuest VLAN 100 ->AP->Primary WLC<via mobility>Anchor WLC<>Checkpoint Int4.100 (VLAN interface)ISE<>Checkpoint Int5Android us...
Clients connecting to specific SSIDs of Cisco 5520 WLC (IOS 8.10.x) are not getting IP addresses and dynamically getting added to an exclusion list, the reason listed as "802.11 Assoc Failure".Expected behaviour: users have to get a captive portal fo...
Recently we upgraded our Catalyst 9800-400 from 17.9.3 to 17.9.4. The following images were installed in this order.C9800-40-universalk9_wlc.17.09.04.SPA.binC9800-universalk9_wlc.17.09.04.CSCwh87343.SPA.smu.binC9800-universalk9_wlc.17.09.04.CSCwh4749...
