Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi!I have a WLC 5508 and 25 LAP 1041. I use two wifi, one with RADIUS for data and other with wpa-psk for voip. The problem is the voip conectivity is broken.How can i improve the handover?The NEC recomendation does not help me anything.thanks!
I have Guest WLAN and i want to redirect all the traffice to Proxy Server. We use Cisco Ironport.Cisco proxy Ironport has the ip 10.X.X.X. We also have NCS Server. Can anybody tells me where i can configure thisbest regards and thanks in advance
I installed the new ncs version (1.1.1.24-small), with success. Later I will use a temporary license for testing.I use the licing center and get a license but I get allways following message : "UDI of file not match the system"Following parameters :...
Hi experts, Q1. How two wism work redundantly together when the host 6500 switches are configured to operate in VSS mode? Are they still indepent two controllers or are they becoming virtually one?Q2. Use one 5508 as primary and 2504 as a backup for ...
Can you convert a ccf file into a file that wireshark can see (ie pcap)...Didn't see anything in guide:http://www.cisco.com/en/US/docs/wireless/spectrum/expert/users/guide/spectrumexpert.pdf
I have an 1142 running capwap c1140-k9w8-tar.124-23c.JA4 that I am wanting to convert to an Autonomous AP.However, the AP does not seem to have an archive exec command to tftp downoad an new IOS.Is there another procedure that should be used?Thanks...
Hi!I have a WLC 5508 and 25 LAP 1041. I use two wifi, one with RADIUS for data and other with wpa-psk for voip. The problem is the voip conectivity is broken.How can i improve the handover? The NEC recomendation does not help me anything.thanks!
Hello,I would like to transform this acces point to an autonomous AP. Is it possible ?Could you tell me how can i do that ?Thanks in advance
HelloCan 3600 series model AP work with WLC 4402 with existing license, we purchased 25 LIC pack and still using only 15.Any recommended Part no on 3600 series with external AntennathanksVishal
All,Anyone know why some of the aps will have CDP enabled upon association with wlc and others will not? I have 3 5508 controllers on the network running over 900 aps.Thanks in advance for your assistance.IzzySent from Cisco Technical Support iPad Ap...
HiCan anyone tell me if the mounting bracket for 3600 AP is the same as the 3500/1140/1040 mounting bracket?I'm suspecting it's not as you can get modules that fit onto the back of the 3600 APs.ThanksMartin
Hi AllI have a problem to get the 3g interface to work, attached it's a configuration and an output for a debug chat. The 3g interface dont support ppp and it only support slip, with slip I can't configure username and password becauseslip dont suppo...
Does anyone know why my aps are showing up as IEEE pd devices and others are AIR-LAP1142N-A-K9?I find when they show up as IEEE they do not join to the controller. However now I am see that some that do show up as IEEE will join ok...however might no...
Hello,I have an enterprise wireless solution with three WLC's in the corp office and about 160 LAP's around the US. The sites are connected via MPLS network. The issue is everytime the MPLS is down, some of the LAP's looses the connection to the WLC ...
I have four (4) 5508 wireless controllers that I would like to consolidate into one (1). I have 100 licenses on one (1) and 50 on the other three (3). Is there a way to pull the licenses off of the three (3) 50's and load them onto the 100 so I end...
