Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Any there a way to stop advertising Cisco appliances on a WiFi network. For example when I logon to our in-band Guest Wifi using nmap I can see the Cisco Controller interfaces and the NAC server trusted and untrusted interfaces as well as the Web Ser...
Would anyone have a copy of the c1240-k9w7-123.8 JA.tar or commonly known as the default file. They don't have it available for download, and I need it to repair a c1242 access point which mistakenly got a 1200 tar file loaded on it!Karl
Hi all, I'm working in an indoor mesh proyect and I'm planning to use a WLC 2112 and 7 APs 1242AG and 2 more 1242AG AP but in local mode. The question is if that WLC is compatible with those APs to support indoor mesh, because in the "Release No...
is it possible to map more than one vlan on one SSID. or more than one AP group per Access point (I couldn't find such possiblility while looking at the WLAN controller GUI or cisco tutorial but I'm still curious if there is any way).
Hi,I was using 1100 AP in which it has some IOS problem so on my boss request, i tried to change/upgrade the flash: c1100 file.So, i deleted the flash file and at a sudden it completely went off red, green, red light order its glowing at status. It h...
If I use machine and user certificates does that mean the machine get's an IP address, authenticates, the user then logs on which causes another DHCP renew and user authentication? Is it better to use machine and user or just machine?
Is there a way to set up web passthrough as HTTP, instead of HTTPS? We wish to set up a hotspot where the only data shown to our users is the Terms of Service. Our users wouldn't provide any info, only hit the "Accept" button. None of this informat...
HIJust updated wisms with ver 7. Went to check with WLC Config Analyzer, but when I run sh running-config each controller it now crashes my telnet session which doesn't give the full cfg. It crashes at the same place each time when ran on the contr...
Looking at the Radio status tab on a Aironet 1200 ap running latest firmware and it shows the software status as disabled and the hardware status as down, but I have the radio enabled. Any ideas?Thanks,Pedro
Hi Problem: When trying to connect to the network using AP it takes about 10 - 15 secs to get reply. But if connected through ethernet its as normal.Scenario: 2 WLC ----> Cisco Switches (3550/3750) ----- > Cisco AP ----> Scanners/Guest Vlans. Authen...
I got PEAP to work using the windows zero config but I cannot get PEAP to work when usin CSSC on the same laptop.When using CSSC I get asked for the password and authentication fails. ACS is reporting PEAP authentication failed due to unknown CA cer...
I have a 1131 AP and it wont respond when I tell it to via the controller to go back to its factory default settings. Does anyone here know if there is another way to whipe the AP?
Hi,I have 1131 access point and by mistake , I have deleted the flash and there is not any file other than ( env_vars ) file . now i am trying to load autonomous IOS but i am not able to do.I have tried setting the IP address with below commandsap: ...
Hi,I have recently uploaded the autonomous ios in 1131 ap and i am able to configure the ap. but if i want to save the configuration in startup config , i am not able to save it.Once i reboot the AP , i am getting default configuration .is it related...
Dear,The vlans created for the mapping of SSID in embedded AP on cisco 1941 can be connected/communicated to the VLAN created on Layer2/3 switch.Lets say i have created 3 vlans (say 200,201,202) for 3 ssid and the vlan created on switch (say 200,201,...
