Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I am curious as to what you all are using for location tracking? I have WCS already in place...Is the location add-on for it the way to go or is something else such as the Ekahau system better? Also, what are you using for tags? Ekahau, AeroScout, so...
We have setup a guest network on our WLC 4402. The visitors can connect using the accounts we setup for them, however, they keep losing authentication a number of times through the day. The clients aren't moving and the devices remain connection to t...
What is the easiest way to connect a 720 switch running a WiSM to a Core running MSFC2 module. Layer2 or Layer3???
From global config. mode, when I create an ssid called "nuaWirelessN", it doesn't take me into the ssid sub interface. When I type in "nuaWireless" it does take me into the ssid sub interface config. Anyone know why that "N" messes things up?Also, if...
I receive the next messages very often from many different ap's. It is always in the same second.802.11b/g interface of AP dsannlmr41 is down: Controller 10.51.244.2 Reason: Unknown. - Controller Name: msannlmr41802.11b/g interface of AP dsannlmr41 i...
Have a couple 1231g's that lived in a LWAPP environment but are now being re-deployed at stand alone units. Can't figure out how to downgrade or turn off LWAPP. How is this done?
Hi,Please suggest any recommendations to be followed in mounting the AP (like wall and ceiling). Specifically I would like to know any best practices about the minimum height for mounting the AP.Regards,Guru
Hi, we are deploying PEAP for wireless access, we had no problem to get this working with laptop vendor supplied wireless management software (which includes 802.1x supplicant), but when I switch to Windows Zero configuration and let Windows XP manag...
Hi,I am using PEAP with mschapv2 and authentication using ACS with AD.The client is winXP/SP2. I am using windows configuration to configure the wireless setup in XP. The client can connect to the network via wireless. But after i disconnect and try ...
Not sure if this has been asked or covered.We have a 2106 (running 4.2.205.0). I was wondering if there was a way to setup a WLAN that uses Web Authentication, where that would use a RADIUS server to authenticate the user instead of having to manuall...
Looking to log client connections along with IP Address and MAC address. Is there a syslog facility that includes this information or a document that lists the various logs that are sent?
Getting the following:Oct 8 11:00:38 wlc-wism1 wlc-wism1: *Oct 08 15:00:38.763: %APF-3-GET_TKN_BKT_FAILED: apf_policy.c:327 Could not get Token Bucket Entry. All token entries are already in use.Oct 8 11:00:38 wlc-wism1 wlc-wism1: *Oct 08 15:00:38.76...
Dear all,From H.Q to the branch office we need to connect using wireless. distance is 9 km.do you think 1500 series AP will be a good option in this scenario. what type of antenna i need to use and approx gain of antenna.can anyone provide directions...
Dear All,I am looking for the last Safe Guide about the wireless enviroment.There is anyone that can help me?Best Regards,Igor.
I have two cisco 1200 that i need to pass traffic from one building to another. I have two 3524 poe switches one on each side. i want to trunk or pass 2 vlans over the radio but i need to set up like a trunk as if i was just trunking the two switches...
