Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hellosome strange issue when a wlan client is connected to guest-wlan (with web-auth from wlc controller) and is starting common client remote access ipsec vpn connection to a target on the internet.The vpn client connects successfully, but there are...
Hi Team,I am having 10 Lwap with 4404 controller in my site.I am facing problem with rauge ap's.I am not able to connect to my network.There are 100 rauge ap near my site....i think my controller is not able to provide channel to my ap's.Please sugge...
Hello,I am installing a 4402 WLC next week and I am trying to determine which IOS version I should install. I see that there are many options to choose from. My pass experiences from talking with Cisco Reps that 5.0 is not good and 4.2 is the safest;...
How do i configure multiple SSID with difrent types of authentication / encryption on on vlan with a WLC 2100 serie?
HI every body!Let say we have following scenariowlan(client) APBoth are configured for wep autehtication using pskwlan client sends request for authenticationAP sends a challenge to wlan client.Will wlan client encrypt the challenge using Rc4 algorit...
I'm in the process of deploying a wireless network for my company. I have the Cisco Wireless LAN Controller 4402 (WLC4402) and the Cisco Wireless Control System (WCS). The WLC has recently been upgraded to 4.0.179.11 and the WCS is running version 4....
Hello, I need to know which users used our wireless lan on sunday. To connect to the wlan they have to type in the wpa2 networkkey and then authenticate with username and password (web authentic.). I could not find a logfile with this informations. W...
If I use the GUI interface to FTP a backup of an ACS SE appliance, what do I get in the backup file? Just the config? Certificates? User database(s)?
We want to do a 1km P2P Bridge using 1252 APs and 3 Yagi antennas.Q: Can I stack the Yagis vertically on a single pole, or should they be side by side horizontally on 3 separate poles?Q: What antenna spacing? I was going to use only about 3 wavelengt...
I want to upgrade my WCS to 5.2.148, but when I review the release notes for that version, the "supported" WLAN controller versions does not include the MD release of 4.2.176, well, its just NOT in the list, they don't say its not supported. Any help...
Hi.I am using a single Cisco 1130AG authenticating to RADIUS on Microsoft IAS (I do NOT have a WLC)I was wondering is it possible to use one flat SSID in my network and then dynamically assign VLANs to users based on matching of RADIUS Policy and RAD...
I have a AIR-AP1231G-E-K9 it is running c1200-k9w7-mx.123-8.JEC2/c1200-k9w7-mx.123-8.JEC2.I am using a Mac Access list to restrict users access to it - however when I add an address now it crashes the AP and has to be rebooted. Is there a limit to Ma...
Hello everybody!I have an Aironet 1200 in IRB bridge mode with defined default gateway. But i need to have an additional static route for some monitoring purposes. Is it possible at all and if yes how to...?
Hi We have 3 new AIR-LAP1131AG access points connecting to 4400 controller with software version 4.2.205.0. The access points connect to the controller and start downloading their software. After a few minutes the access points reboots and starts ove...
I read the guide and found that, the rogue detector need to use trunk link connect to switch, does it means we need to change the native vlan respectively (vlan 1 won't be use in normal situation) and is there any special configuration need to do at ...
