Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Would anyone know if I would run across any issues when upgrading from a Cisco Wireless controller WLC-12 to a Cisco wireless controller WLC-50? Can anyone forsee any issues with me just copying the startup config from the WLC-12 to the WLC-50? Any a...
hi there, I have this wireless access point but i cant configure it. I can see the boot with the hyper-terminal windows (xp), the ip adress is 219.1.1.179 (dhcp) but i cant go on with IE or Firefox. When im on a console text (AP#) and want to configu...
Would anyone know if I would run across any issues when upgrading from a Cisco Wireless controller WLC-12 to a Cisco wireless controller WLC-50? Can anyone forsee any issues with me just copying the startup config from the WLC-12 to the WLC-50? Any a...
Here is the problem I need to solve.A family member has a dialup connection.Dialup being a 56K analog modem. They would like to bring a wireless enviroment into their home keeping this 56K analog modem in place. To be specific as possible in the conf...
Dear AllI just want to create two SSID with two different VLANs , on AP 1121G , and broadcast the two SSID , how can i do it ?i know that in my switch, the point connected to AP must be trunk , do i need to create BVI ?!!! and do i need to make ether...
Hello.Can somebody tell me, how can i configure for radius's client attach fixed group?I have 5 client's - and everyone must use for access only one group?Some body know - can i do it theoretically and if i could - maybe you know usefull link?Thank y...
Dear All, my customer has a central to 30+ remote site management solution via ISDN and works fine.Now he needs to have 3G on his central site calling to ISDN ports at remote sites, i tried explaining that its not possible as these 2 technologies hav...
Hi There,I have a general question concerning BVI & Dot11 interfaces on a 871W. I had to configure a Subinterface for the radio Interface to get he box running. This is the point which is a little confusing to me. Why do I have to work with subinterf...
My large 4 controller outdoor mesh network does not use RADIUS, so I went to the 4 WLANS and set Security>AAA to not use it. Prior to this I was getting a stready stream of Syslog messages from the different WLANS complaining about not being to find ...
We have a 5.2 WCS Software with 5.2 WISM Modules in 6500 Catalyst. When a new access point registering at the master controller we could see it as AP0001.0002.0003 (for example). When we rename it to AP-70 and setting up the backup controller I could...
Does the BVI interface work on the native VLAN or always on VLAN1 on a 1300 bridge? If I set a VLAN other than VLAN1 for native will that move the BVI to that VLAN? Also, does the native vlan have to match at both ends or does it only have local sign...
hayI have two WLC 4000 configured as failover.does the configuration synchronize between the two WLCs?
i have a wireless lan with wlc.the wlc has some vlans, also 1 vlan which is the same of the wired lan.if i connect to the wlan 1 get a message of duplicated ip even if i get an ip that is no used by any host.can anyone help me?
We have a lot of AP1231G APs that are due to lease refresh soon. We will likely be buying lightweight 1232AG radios to replace them.Some of these have antennas in very hard to reach places. How critical is it to replace the antenna for the 5 GHz band...
What is the most stable OS for the cisco 4402 WLAN controller?
