Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
What is the best practice to use when configuring port channel between Catalystr 3750G switch stack and WLC 4402 / 4404 Wireless Lan Controllers:a) Negotiate to LACPb) Negotiate to PAgPor c) Hard-code to Port Channel without any negotiation.Any point...
I have 8 Cisco 1230AP's providing access to my LAN for laptop users. The encryption is via WPA. I now need to setup unencrypted access to the internet for guests/visitors - keeping them away from my LAN and internal network. How can I do this? Do I j...
I have 8 Cisco 1230AP's providing access to my LAN for laptop users. The encryption is via WPA. I now need to setup unencrypted access to the internet for guests/visitors - keeping them away from my LAN and internal network. How can I do this? Thanks...
I have a network that consists of 5 1310 bridges. One is in Root+AP mode and servers as the central node that all others talk to. Today all of the bridges are open with a single hidden SSID. I would like to begin migrating these to WPA encryption. I ...
Hi There,I just have one CiscoSecure for both Web Auth and 802.1x.When working with WLC, how can we distinguish the user that is logged in by Web Auth or 802.1x?Thank you.
Hi all,Can wireless client associate AP by existing loading of AP but not by wireless signal strength?Thanks & Regards,Eric
Hello, I've got a cisco 1240AG K9 AP plugged into a DSL router. It has a factory config with DHCP enabled and one SSID. This AP is set up for open, unsecure internet access in our dining areas. Problem is, I have office PCs in the vicinity jumping on...
HelloI tried to alter the vlan configuration for the management interface on 4402 controller. The management interface are tagged with the vlan 55.Now, I d'like to change this vlan 55 definition to a untagged configuration. On the corresponding switc...
First time playing with c1252 and I got some issues. 1.I enabled all the high throughput rates, set WMM policy to 'Allowed' under WLAN and tested with open authenticated WLAN under 2.4g. But I only got 65M on both Linksys 300N card and a Macbook. Wha...
Hi,we use several 4402 wlc and want the aps connect to connect to them via dns discovery.It would be fine if somebody could tell me to which ip address (in our dns database) I have to add an alias for cisco-lwapp-controller.<domain>.Is it the managem...
Hi,i have 2 cisco aironets 1240 connected on site-1 to a 3750 and site-b to a 3560 switch...i've called TAC a few times to help with setting up an EtherChannel beetween these 2 bridges but they have no clue how to do it...every tech tells me somthing...
Can anyone advise on how to use the Local EAP in WLC. I'm trying to set up EAP-FAST authentication for the 7921g phone without ACS. I have a Windows IAS available but I couldn't find support for PEAP in the 7921 even though the documentation mentions...
Wireless Domain ServicesThe problem: I am using WDS in my wireless networking environment, and a new building is going to bring the tally of access points to over 60.The question: What is the best WDS solution for this problem?Other Questions: Is it ...
The company I work for has all its APs controlled by a WISM. I recently deployed an AP out to a WAN site and when the AP boots up, I am able to see on the WISM, able to ping from the WISM and vice-versa, able to ping the IP addresses of the SSID from...
Hi dear,i configured two (2) 4400 Series WLAN Controller as cluster (one primary and one secondary - Active & standby)...It works fine...But i have only one concerns:During my clustering tests, i noticed that when i switch-off the primary all Lightwe...
