Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi,I have a question about your WLAN Cisco 4404. I have a plan with 62 AP AIR-AP1242AGLightweight version (LWAPP). The AP will be distributed on three levels with twotechnicals offices. I want to install two POE switch per level connected with the AP...
dear sir, We are trying to setup the access point AIR-AP1242AG with wireless pcmcia AIR-CB21AG for wireless site survey. Please provide me any configuration that suit the mentioned access point for site survey usage. Thank you and your effort shall b...
Someone Knows, if I can connect an AP 1131 configured as WGB to other AP 1131 acting as root with 2 Vlans and 2 SSIDs, and pass all of them to the WGB ethernet port, a mean, passing the traffic from the 2 differents VLANs with two differnts IP range ...
dear sir, We are trying to install the ap1241 with special antenna / antenna booster that could deliver single line direction of signal. The ap1241 will serve to the end user in noisy environment with surrounded by machines. We understood that ap1241...
Hi,I have a WLC_4402/wcs and two wlan. One is private with authentication and other is for public access to web, without auth. I want to define a length of time (exemple 2hs) that a client is allowed to surf the web and after that amount of time the ...
I'm installing sites with multiple AP's. When I receive the AP's they have various levels of firmware.I have no problem updating the IOS firmware, but am also receiving two different versions of the radio firmware - 6.10.2 and 6.20.2. I haven't been ...
Hi, I have a single AP setup using PEAP with MS Win2k3 IAS/RADIUS. I would like outside vendors and clients to be able to come in and be able to access the Internet as well as a printer. I believe in order to authenticate with PEAP the laptop must be...
I'm new to AP's. Need to know if the 1310 AP can do multicasting and/or igmp. Any doc availabiel that would be helpful??
I just inherited a wireless LAN that is using 5 1230 WAP devices, all using a single SSID configured for 1) open authentication, 2) mandatory WPA key mgmt, 3) hex SSID key, and 4) cipher TKIP encryption. Everything works fine, but now I have to add a...
When adding a guest user with a lobbyadmin id, is it possible to assign that user a QoS role.
How can I change the password for controller based Access Points on the WCS?On the controller itself I know how it is done.( config ap username <USERNAME>password <PASSWORD> <all | AP Name>But how is it done on the WCS wher 3 controller exists?Thanks...
Hi! My requirement is to connect the access point to an Internet Router through a common L2 switch so that wifi-enabled laptops will receive public ips through the DHCP pool defined on the AP and be able to access raw internet. The Internet Router ha...
We upgraded our Wireless LAN Controllers from 3.2.78.4 > 3.2.195.10 > 4.1.185.0 > 4.2.99.0.We are implementing Vocera and they are requiring that we degrade the Wireless LAN Controllers to 4.2.112.0. Is it possible to degrade without losing any confi...
During the site survey, we used the 1230 and assigned tx power based on 100mw, 50, 30, 10, 5.. so on.. on the AP. But when we implemented the controller-based, the transmit power were replaced with 'tx power levels', 1,2,3,4... so on... I read somewh...
Hi,I've got a WLAN consisting of (2) 2106 controllers and (10) 1131AG APs. The controllers are in a Mobility group - same name, both can see each other, same virtual IP. QoS is set to Silver (best effort). I have a single SSID.Currently only about 5 ...
