Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi Mates,Please I need your help to fix my old br1310 restarting problem I did a software upgrade but still can't pass it!! next is show version command result:bridge#show versionCisco IOS Software, C1310 Software (C1310-K9W7-M), Version 12.3(7)JA2, ...
I have configured My Aironet 1100 with WPA as follows:TKIP for Encryption and 802.1x with EAP for authentication, PEAP And Also ACS v 3.3 as authentication server with MY AP client RADIUS (Cisco Aironet).My problem from time to time "not fixed" asked...
How can I setup login to AP's using Tacacs autentication. I currently have all the Ap's set up for local autentication. commands most welcomeAp's 1210 Running V 12.3 4 JA1WLSE 1310 V2.11and Cisco ACS Thanks,
This is more a question born out of curiosity. Why did Cisco choose 'tsunami' as the default SSID on the vast majority of their products? Is there a reason behind this?
Hello, would appreciate some feedback..I understand that the AP can receive ip addresses for WLAN clients from an active DHCP server on the LAN. In that case, is the AP acting like a bridge with the interface to the LAN having the same IPs as the on...
Hi.I have a Cisco AP 1231G, which is connected on the LAN. I purchased a Netgear WG602v3) to configure it as a "wifi client" to connect a printer on its RJ45 port. I configured the Netgear and it detects the Cisco, but the Cisco doesn't detect the MA...
Dear all my expert, Together attached the floor map after site survey. i.) please provide me sample configuration template based on the floor map. ii.) Please provide me the receive sensitivity(typical) for 802.11b standard. Please advise. Your ef...
How can see if an 1120 AP has been upgraded to support 802.11G? I have been told it suports 802.11G but in the Web GUI I can only see 802.11B.The system software version is 12.2(13)JA4.
I am running WLSE 2.12 express. I have my 7920 IP phones registering via leap all using the same username and password on the phones. Encryption keys are set to regenerate every 3 minutes.If I login to my WLSE box and go under ADMIN -> AAA AUthenti...
I have set up a 851W and had no real problems. The problem I have is the signal strength is erratic varing some 30 db measured with two different meters. At times it appears to loose all it's signal momentarly. I have varied the CCk and OFDM transmit...
Is there a way to add multiple syslog servers to the 4402 controllers? (version 3.2.78.0)I know I can do this via a load balancer to a virtual ip address for a log server, but I would rather avoid the extra hardware & configuration.
I have a 871w router up and running with dhcp on the router for vlan 1 assigning 10.1.5 addresses to cabled clients. I also have the nating working correctly for the outside interface and VPN working correctly as well. I can't get dhcp working on t...
Resolved! Anyone see this error on the WLSE?
Yesterday I noticed I started getting the following error messag on the WLSE when trying to view an AP config from within the WLSE"Login failed, wrong credentials provided or Telnet/SSH disabled on this device" I never received that message before. I...
Access Point Memory Exhaustion from ARP Attackshttp://www.cisco.com/en/US/products/products_security_advisory09186a00805e465b.shtmlblock arp attackthis problem is correct ? (below)interface Dot11Radio0 l2-filter bridge-group-acl bridge-group 1 input-...
Dear all;I have a AIR-AP1121G basestation. Recently upgraded to software version 12.3(7)JA2. Now it's reporting it has a 11B radio and hence the wireless interface is down and won't come up. See:bhap01#sh int dot11Radio 0Dot11Radio0 is reset, line pr...
