Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Welcome to the Cisco Community Ask Me Anything Event   Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...

Shree Hari AB.jpeg Screenshot 2026-09-11 at 3.12.04 PM.png

I am converting from Aironet 1231 APs to Cisco 1010 LWAPP APs in the near future. My question is will the power injectors that I am using with the 1231s (AIR-PWRINJ3) work with the Cisco 1010 APs? Voltage requirements appear to be the same according ...

c.fuller by Level 4
  • 1633 Views
  • 1 replies
  • 0 Helpful votes

I am out of .....I have to AP 1210, one is the WDS master, the second one is a WDS client. The client AP is registered in the master. But houw must i configure the client AP? i am running two vlan's on the master.What to configure on the client? Same...

I am interested in creating a guest internet WLAN using LWAPP AP 1010s and the Cisco BBSM. Are there any issues that I should be aware of or are the AP1010s compatible with the BBSM? I have attached a high-level diagram of what I am proposing.Thanks,...

j.teeter by Community Member
  • 507 Views
  • 1 replies
  • 0 Helpful votes

Could you please help me out with the details of the Aironet 1310 AP/bridge..a.) Make CISCOb.) Model AIR-BR1310G-A-K9c.) Freq Range 2400-2483.5d.) Freq Control ________________e.) Rated Power ________________ f.) BW&Emission ________________ g.) Cond...

gsjuguilon by Community Member
  • 647 Views
  • 2 replies
  • 0 Helpful votes

Hello,Is it possible to utilize EAP with Active Directory + Radius Win2K without the use of ACS or a CA? Can I manually install the required certs to make this happen?

lxcollin1 by Level 4
  • 424 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Air-AP1200

I am going to order "AIR-AP1231G-E-K9", and it requires external antennas. I need antennas directlty connected with this AP without any cable. Is "AIR-ANT4941" correct antinna for this requirement. If it is correct selection, do i need to order two "...

rehan_uet by Level 4
  • 816 Views
  • 1 replies
  • 0 Helpful votes

Greetings,I'm fairly new to all things Cisco. I've purchased two Cisco 1310 bridges and, for the life of me, cannot figure out where I can download the latest IOS for the Bridges. Can anyone point me to a link that actually works? Is there some secre...

basimnasr by Community Member
  • 725 Views
  • 3 replies
  • 0 Helpful votes

Has anyone experienced a freezeup of their laptop running the CB21AG card and Windows XP? I have this happen periodically - the LEDs stay solid and I have to remove and reinsert the card to resume. Thanks!

wififofum by Level 7
  • 636 Views
  • 3 replies
  • 0 Helpful votes

I have question about signal of Cisco's AP. I have used two APs, Cisco Aironet 1121G, for each floor. My problem is when I'm first floor, I will associate with AP of second floor.I would like to know how I can adjust access points's signal strength. ...

chaiwat_t by Community Member
  • 895 Views
  • 1 replies
  • 0 Helpful votes

A customer (a truck inspection site) needs Wireless access outdoors in thier truck inspection area. I'm going to install a Mast Mount Antenna outdoors and run a cable to an Aironet 1200 indoors. My question is, do I only use one(1) antenna or two(2)?

edwardsjj by Level 3
  • 548 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card