Wireless

I am trying to set up PEAP-MS-CHAP v2. I am using Windows 2003 with IAS, Cisco 340 AP with 12.03T, Cisco 350 Wireless Card, Windows XP SP1. After logging with wireless user account, it connects, authenticates, and associates with AP for about 5-7 sec...

Hello all, Here is a peculiar problem for me a. I have got CISCO 350 Wireless LAN adapter for Ipaq Pocket PC 2000(Win CE 3.0)...AIR - PCM352 to be precise.. b. Yesterday, I was able to connect using through the wireless access points... and the devic...

I thought I would share the solution we found.Enviornment,Mixed hardware clients, all WIFI compatible.Cisco 1231 AP'sCisco Secure ACS for windowsWPA with PEAP Problem,Clients utilizing WinXP SP2 and wireless zero conf were not able to connect to our ...

With 2 sites using two 1300 bridges as a wireless link between the 2 LANs, what is the best mode to put them in if I only want the wired traffic to pass....not other AP's or Clients?

All,Can someone please explain the deauthentication reason below from my 1200 event logs:Reason: Previous authentication no longer valid.What causes this? I'm using non-Cisco clients - is there a specific inactivity time out that causes this?Thanks!

Hi,As per my understanding the 1200 Series Access points running IOS (12.2(15)XR) send the management traffic (RADIUS,Accouting NTP etc) un-tagged i.e. using VLAN 1.As per our current setup, we assign this un-tagged traffic to a different VLAN (by ch...

Can someone explain the difference between the cipher TKIP and the cipher TKIP w/ 128bit WEP? I thought you got a key when you selected TKIP...Thanks in advance.David Beaver

I live in Serbia and Montenegro where local regulations gives 100mW on 2.4GHz. Unfortunately, I am not able to set the power output to more than 50mW on 1200AP. Is there any possibility to "unlock" the radio and to use 100mW? Any answer is highly app...

Hello,I have problems deploying PEAP. I have ACS3.3 in Windows2000 Server; AP350; client Windows XP with PCMCIA 350. All is configured as it says in the docs.I am working with the ACS local database. Certificates and all the stuff is ok.I attach the ...

I have had 4 350 series access points that all of a sudden will not allow clients to associate. All were running vx works 12.03T. There were no configuration changes made on any of them. Any ideas?

Goodmorning..I have a four bridge setup, two spearte SSID, with a cross over in the middle. ME*-rootA<--->non/rootA---rootB<--->non/rootB*ServerBI have a solid link over a ten mile area. Couldn't be happier with the peformance. Lan traffic does pass ...

We have two Aironet 1310, connecting two office buildings. Association works fine, they get linked at 54MBit/s. But when we measure throughput, we get results between 8 and max. 15MBit/s.We can see CRC errors climbing up, but signal strenghts is quit...

Dear Sir,I would like to auto generate a new session key every 30 minutes running LEAP using AP 1200 Local RADIUS authentication? How can I configure it? I noticed there is a session timeout option under Security-->Local RADIUS Server-->User Group, i...

Is there a way to configure the Cisco ACU installation with a 352 PCMCIA card to interact with a Cisco 1200 setup for WPA-PSK.Thanks,Dan

Hi,We have 2 1300 Bridges, last firmware version.In the same room, Bridges seeing together, one is root, the other is non root, link is ok.We disconnect on bridge, going to antoher place, about 2 kilometers, reconnect the bridge. At this time, the Ra...