Wireless

I trying to setup a AP1200 radio with two different SSID's with encryption.Each SSID must use a different 128 bit WEP encryption.Both SSID's must have simultaneous access to the wireless radio.I get the client & radio associated but can not pass data...

Has anyone heard about when Cisco plans to implement 802.11i, now that its been ratified, in its wireless IOS?

Can anyone tell me what is the maximum length of RJ45-RJ45 flylead (the one between the bridge and transformer) I can use?The idea is that while I have the bridge close to the antenna, I can use the 80m flylead to supply power to the bridge from our ...

I about to install (never have installed wireless before) a outdoor wireless backbone as such;building 1 ------ building 5 -------- building 6Building 1 & 5 will have an omni antenna and building 6 a directional one.There will be no wireless clients ...

Recently we install 2 wireless sites using the following:Site A -Root BridgeAIR-BR350-A-K9AIR-CAB150ULL-RAIR-ACC3354AIR-ANT24120Site B - Non-root bridge Without ClientAIR-BR350-A-K9AIR-CAB050LL-RAIR-ACC2662AIR-ANT1949AIR-ACC3354We did the antenna all...

Has anyone been able to figure out how to cache LEAP credentials under the Cisco ACU for Linux?Cisco 350 miniPCI, Dell C840 Latitude Notebook.Firmware is 5.30.17ACU is 2.1.13Driver is mpi350.oRunning on RedHat Linux 9, Kernal 2.4.20-8 Thanks for any ...

Problem: Toshiba Tecra 8200 Wireless LAN Card successfully associates with Cisco 1100 AP using 128bit WEP key however the client fails to obtain an IP address from DHCP server on the same physical LAN as the AP.If I view the association detail on the...

I've upgraded an AP1200 to 802.11g. I can use a CB21AG client at 54Mbs OK however I can't get the backward compatibility to work for a 350 client (802.11b). I have one SSID.I have speeds configured as follows;speed basic-1.0 basic-2.0 basic-5.5 basic...

HelloI would like to hear from you otu there what are the best security setting for a P2P bridge outdoor link with two 1310 bridges. (with/without external Radius).any input is very welcomeOliver

Hi,I am running several Cisco 1200 Series access points, running a mixture of VxWorks and IOS. At the moment I block everything but PPPoE (ethertypes 0x8863 and 0x8864) using the ethertype filters section of the web interface. I would like to add a m...

Hi, I have ordered the antennas with the wrong connector types and want to order the correct connector to plug into the AP. I know that I need a male RP-TNC connector, but does anyone know what LMR # I need or where I can find the docs with this info...

I have a 50+ access point deployment, all in a single VLAN (DMZ), across a dozen buildings. We recently experienced wierdness of the following sort. Clients would request DHCP request, DHCP servers would forward requests, which would not get passed f...

We need to connect two points with a wireless Bridge. One Point is on Bahamas and the other in Miami (57 Miles).Use: Data / VOIP We appreciate any recommendations to do this.

I press the "mode" button on the back and hold it for a while after plugging in the unit and it will not reset.Cisco AIR-AP1220 B SeriesIs there a secret to this?Thanks in advance....

We have noticed a recurring problem with some of our AP1231G's. When they are deployed, we can see the AP and see that there is a wireless connection, but are not able to transmit network data or ping the AP. However, if we cycle the power to the AP'...