Wireless

I have 8 pairs of 1200's that I am setting up with hot standby and I've seen some odd things. When I successfully establish hotstandby, I notice the role of the access point changes from Root to Site Survey Client. Is that supposed to be that way? I ...

Hi,I have few WLAN questions, and would highly appreciate your expert opinion.1. Please let me know if I can connect access point antennas with the PCI client adaptor. Also can I extend the built-in 2.2 dbi dipole antenna using low loss cable upto 20...

Our entire wireless infrastructure is made up of Aironet 1200s and 350s. We are currently in the planning stages of rolling out Active Directory. I wanted to know if there is any suggestions on how you would"break out" a seperate wireless OU and how ...

Is there a timeout for web access for the 1200 ap running vx works. After a few minutes I loose web connection and I have to reboot the AP so I can get back in. If there is a timeout where can I change that setting.thanks,gilbert

Hi,I'm wondering if Cisco Mobile IP will support wireless devices access across subnets even while using IPSec tunneling, without the need to re-authenticate.Any info would be appreciated.Best,Marc

I have a aironet350 AP with Laptops connecting to the AP. The Clients connsct to the AP Fine. I use Static IP's in my environment. I can ping a laptop from the AP, and from the switch on the local LAN. This is a remote branch that i connect to via a ...

We have aironet 350 client adapters installed on tablet PC's and Laptops. When upgrading to the new arionet client utility 6.2, Firmware Version V5.20.17 and NDIS Driver V3.5.13, we encountered a problem on every tablet and laptop upgraded. Everythin...

What are people using on wireless networks that have VLAN's for voice and data to provide Layer 3 roaming funcionality. Need wireless voice users to be able to roam across subnets seemlessly. Layer 2 works great but scalling to 2000 users. Need a Lay...

Can someone tell me if this setup will work and give priority to Voice?Building A350 Bridge 3550 SwitchBuilding B350 Bridge2924 SwitchI will want to prioritize voice over the link between the 2 buildings. The customer will be using an Avaya IP phone ...

Hi,My WGB350 is showing the following message:"0:01:10 S Unable to determine radio type !"It allways happens a few minutes after power on the radio. I updated the firmware to 8.85 but the same problem persists.When it happens, the telnet header shows...

How would I go about configuring an Aironet 1200, that is a stand alone, to be used in a site survey function. I want to push this AP on a cart and leave it in a place that I think is a good location for an AP, and conduct a site survey based on this...

I have a working PEAP (MS-CHAPv2) environment using Win2003 IAS, WinXP sp1 machines, and a Cisco 1200 with 12.2(13)JA1. Here's the problem. I can get any vendors card to work with this except for the Cisco 350 series cards.And the question. Must I in...

Cisco Aironet 350 802.11b card working with 3rd party wireless DSL router (LinkSys, D-link or Netgear) to establish VPN tunnel via Cisco VPN client. VPN session always get drop when using 9600 MHz cordless phone. Is there something between Cisco Airo...

I am seeing a high rate of CRC errors on the recieve end of my root radio for a point to point connection. What could cause the high CRCs the other end has low CRCs.

I am trying to upgrade [AP350, 12.03T] with AP350-Cisco-IOS-Upgrade-Image-v2.img (12.2(13)JA1 )When I try to save the Firmware-Job I get the following messageImageAP350-Cisco-IOS-Upgrade-Image-v2.img (12.2(13)JA1 ) Not recognized And in BOLD REDVxWor...