Wireless

originally i had wlse 1.3.1 and 1220s, 340s, and 350s. i got the wlse to discover all of the ap's and i was a happy man.now i have upgraded my 1220s to IOS. the 340s and 350s haven't changed. and i upgraded the wlse to 2.0. now i can't discover anyth...

Hello all Cisco users!I am experiencing an extremely slow web-browser interface. I click on any menu option such as EXPRESS-SETUP, NETWORK MAP, ASSOCIATION, etc. and the IOS takes more than 30 secs to send the page to my browser.In a normal situation...

I have a few Aironet AP1000-E's and I am looking for more info on these units; I found the User's Guide for the 2000 and 1000 series WAPs for Ethernet on Cisco.com (after much searching)...Of course, this is a small (12 page) manual and it refers me ...

These are the IOS version and Firmware version for my client : AP1100 : c1100-k9w7-mx.122-8.JA Aironet 350 Client Adapter : V5.02.19 These are my setup, and both running on non-overlapping channel within 10 feet. Switch / \ AP AP Things configure at ...

Design condition1) point to point only 2) no any voice gateway or callmanager3) low costIs the following design possible ? (analog phone & ethernet device) - ata188 - wireless bridge 350 -(wireless)- wireless bridge 350 - ata188 - (analog phone & eth...

After successfully uploading the flash via ftp, the image was decompressed and in the middle of the process it went south. I reviewed other posts and found the unit had been sent to the factory or the owner was out of luck. Is there a do-it-your-self...

On a Aironet 350 non-root bridge is it possible to disable 801.1q bridging on the Ethernet port only? ie leave it on the Radio side side only

I have tried to upgrade the firmware on a 340 bridge, the FTP transfer was ok bu then the unit crashed when it tried to uncompress the image. The unit is now unresponsive, it has a solid red LED and I cannot access the console port. Is this unit now ...

I followed the instruction to flash the formware via the console. I erased the Flash but was unable to upload the image. Now, each time I connect via the Console port, the Express Setup is no longer there. All I see is the main menu.I could see 2 fie...

Hi,I wounder if there is any way to shut off a 352 client adapter (it's a PC-card in a handheld computer) from within a program (API call) ? The power consumption is a bit high for the battery, and since the card is only used a few minutes every day ...

I have AP 350 version 12.03T, 340 Series PCMCIA firmware version 5.20.17,Windows 2003 Active directory domain and Windows 2003 IAS server. Client PC is Win XP, service pack 1. I was looking into EAP-TLS versus PEAP. I understand that with EAP-TLS, yo...

Hi All,I configured the access point with username/passwords. The usernames are not the runof the mill usernames. Now I apparently forgot the username and even with console in, Its asking for the password. Becoz of which i cant even configure the AP ...

Hi, I have a client who tells me his only reason for requesting 11g is that he has thick walls at his location. Is he right to do so?I know the obvious answer here is to perform a site survey and do the tests but I would like to know if 11g is any be...

We have 350 APs running 12.02T1 software and 350 series Aironet clients. I am trying to set up PEAP authentication with SecurID and enable Dynamic WEP with MIC and TKIP.I am using multiple SSID's and VLANs to set up three network types:SSID 1 = PEAP ...

I have a wireless bridge setup to use LEAP. On rare occasion, the bridge communication will fail. The LEAP authentication will fail. I have to remotely reset the root AP. Can WPA be used with shared-keys to safely secure the bridge communication.The ...