Wireless

Hi all!The topology is a pont to point bridge link with 350 series bridges. rootbr<------WLAN---------->Non-rootbr<---->switch<---->Ethernet hostsSignal Str. 35%What could cause the following?The link is working corretly, But about half an hour or ra...

Two days ago I got a shipment of access points(brand new) with 12.00 software installed. To my wonder I tried to configure the access points as a root access point but it reverts to repeater access point(radio role). Also these access points came as ...

Do the cisco 340/350 series of products, access points and clients, perform weak iv filtering? I haven't been able to find any reference tothis in documentation or a search of this site.Tye

I would like to enable LEAP authentication for an Aironet client PCMCIA card installed in a DOS based mobile-PC. According to the documentation there is a program called AWCLEAP.EXE - but this is NOT included in the downloadable self-extracting archi...

[all are 350-series devices on 12.01T1]I have a (client) bridge at a remote site picking up a signal from the (root) bridge on channel 2. At the same site where I have the (client) bridge I also have an access point transmitting on channel 10. Both...

Assuming that I simply have two 350 wireless bridges between two subnets 192.168.1.x and 192.168.2.x with no routers whatsoever what IP information should I be entering in the client PC's to connect with the other side. I was thinking that changing ...

Hello.i have a question.I'm trying to use a cisco BRIDGE aironet BR350 as an access-point.I'm using a PCMCIA card model AIR-PCM350.But, until now, I'm not able to associate this card inthe association table of the Bridge.Did someone already used this...

I have 2 AP350 (12.00T); they work on 2 channels (1 and 6).I have configured a MAC Filtering to permit access to network to 10 Wireless Device.Some times one Devices is stopped (Telnet session stopped) for 1 or 2 minutes; I found in the Event Log o...

I got a job that wants to charge users who visit their business for Internet access. We are looking into putting Cicso 1200 series WAPs into a few rooms. We are concerned someone with a laptop will be able to boot their machine up and using DHCP g...

I am told that the maximum throughput on a 11mbs 802.11b connection is somewhere between 5 and 7 Mbs! Is this true and does it also apply to point to point bridge links?

Ok, so far I got the building to building bridges down. I am going to use the Aironet 350 Bridge for a point to multipoint configuration.Now, the inside LAN portion of this wireless network.I see Cisco has 1100 and 1200 series WAPs. Which one shoul...

Hi i want to check the cpu from a wgb 350 over snmp. i have downloaded the Aironet Mibs from CCO for WGBs but i dont know if there is the right oid for the CPU. what is the OID for CPU in the wgb?thxBernhard

By viewing the web interface of the 1200, it lists the "To Station" and "From Station" number of packets (and errors, etc.). So that indicates there are counters tracking traffic for each.What is the SNMP OID to retrieve this via SNMP so that we don'...

Hi all,Im designing a wireless network for around 60000 nodes. Im new to the Wireless networking. I want to know how much users can be accomodated in each level of cisco products like aironet 350, 1200 etc. is there any impact on performance if more ...

Hi guys,I have 2 type of wireless network card, Cisco 350 PCMCIA and a Orinoco card.I should authenticated to the RADIUS server.If I configure the AP (aironet 1100) with the "authentication open eap eap_methods" in my SSID, the authentication on Orin...