Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi,Still dealing with the filter configuration on AP350.Filters can be designed based on the ETHERTYPE, IP protocol and IP port. Focusing on ETHERTYPE filters, how can I filter out 802.3, 802.2 frames ?Thanks and best regards,Guy

gverr by • Level 2
  • 796 Views
  • 0 replies
  • 0 Helpful votes

Hi there,I am trying to determine the best products to improve the strength of a wireless network I manage. This network is located primarily in a 5000 square foot building. I use a 340 series AP and 340/350 series PCI and PCMCIA cards. Performance i...

todd by • Community Member
  • 2206 Views
  • 7 replies
  • 0 Helpful votes

I am setting up a link of around 13 miles but I won't be able to match antenna height at both locations. The root system's antenna is at a hundred and twenty feet and the client node's antenna is at 75 feet. I would like to know if there is a place I...

kbarrow by • Community Member
  • 1419 Views
  • 4 replies
  • 0 Helpful votes

Has anyone out there managed to get Hot Standby working on a secured WLAN with LEAP? I cannot manage to get my clients to do anything more than roam to a different AP with LEAP. When I enable the standby on the second AP and take down the Ethernet on...

dsnider by • Community Member
  • 800 Views
  • 1 replies
  • 0 Helpful votes

himy cisco br342 bridge firmware is 8.24v. i wanna upgrade it to 8.65 or higher. how do i this?would you please tell me that what kind of Firmwares is best for me.i have two aironet342 Bridge, and have 4Km distance from eachother.and i have 2 Andrew ...

mmasha by • Level 2
  • 983 Views
  • 1 replies
  • 0 Helpful votes

I've been having a recurring, intermittant problem with DHCP-assigned IP addresses not getting assigned to Aironet 350 equipped Compaq iPAQ PDAs. I've upgraded the card (4.25.23) & AP (11.10T) firmware to the latest versions. iPAQ client software is ...

mark by • Community Member
  • 1739 Views
  • 7 replies
  • 0 Helpful votes

I need to provide wireless Internet accesss to many customers that already have Cisco 340 series client adapters installed on there systems. Some of these customers are 20-30KM aways. Can 340 Series base station do this job.

adebowalen by • Community Member
  • 1299 Views
  • 4 replies
  • 0 Helpful votes

Is anyone using Cisco ACS in a mixed NT/Netware environment? I can authenticate using the NT database, but am unable to obtain access to Novell Resources. I can log into my NT account and get access to NT resources, but am unable to see Novell Resour...

tcmob by • Community Member
  • 1380 Views
  • 4 replies
  • 0 Helpful votes

We were using UC4800 universal clients connected to P.C.'s and printer via straight thru ethernet cables to attach to the network(AP4800E). Because Cisco no longer manufacures the UC4800E we purchased the Air-WGB350. It appears that we now have to us...

rx33328 by • Community Member
  • 816 Views
  • 1 replies
  • 0 Helpful votes

We are looking at a point to point RF link over Western Multiplex Tsunami (45M) Ethernet bridges. Has anyone deployed this gear before? This is 5.8G license exempt shot.

abrahamj by • Community Member
  • 927 Views
  • 1 replies
  • 0 Helpful votes

Hello!Is it possible to establish and maintain a WLAN connection when moving fast? For example:Nearing an access point with a car (approx. 60 KPH), establish the connection, transmit data and dropping the connection when out of reach.Thanks for any i...

rfalk by • Community Member
  • 876 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card