Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello, I have a Cisco wlc 9800 running on 17.9.6 and it's working fine. Once I'm upgrading to 17.12.3 or 17.12.5 or 17.15.3, all Radios are down on 9166I-ROW APs. There is one outdoor AP 9124 which is working fine on those IOS version. 9124AX has -E ...
Hello all, is there a way to configure Radius - call-station-ID and NAS-ID from the GUI of the WLC? I found this guide https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-9/config-guide/b_wl_17_9_cg/m_radius-call-station-identifier.html...
Good DayWe have a few Ap's C9115AXI-E , manufacturing date 04/22 .Other Ap's will be plugged into the network and they will see the WLC automatically . These once keep on booting . I believe the fix on Cisco's website is not applicable with these spe...
Wireless firmware versions MR 32.1.3 changelogImportant noteMR45/55 APs are not supported on MR 32.x.x and will instead upgrade to the backup version (MR 31.1.7.1) if they are in networks configured for MR 32.x.x versions, and thus, new features will...
Select IPV4 check-box in the General tab, update the fields as per the below image, and then click Click Update & Apply to Device. After performing above step the C9115AXE-D wireless AP continuously blinks Red/Green.Whereas performing same action...
Hi Currently, WLC9800 is a WAP3 only configuration, and when you try to connect Apple equipment to wifi, you often find it looping like a picture. Have you ever seen this?
Hello.I have a question.I purchased a CW9176I (configuration management from the cloud).I conducted a simple test before delivering it to the customer.I connected 200 virtual wireless devices to the AP(Radio2),but only about 150 could be connected. 5...
Hi Everyone,Seeking for your help if there is any resolution on my issue encountered.As of now, some of my users is not able to connect with wireless connection from the captive portal. I have done some packet capture during the authenticatiom until ...
Hello, I hope someone can help me figure out how to set up manually specific Tx power levels, channels and channel width in the 9800 series controller for each AP or groups of APs. Thank you in advance.
Hello all,We have been using a C9800L with the 9115 APs for about a year now and it has generally been a good experience. Recently, some of our users have been issued new Microsoft Surface laptops, using the Intel WiFi6 AX201 160Mhz adapter. At l...
Hi all, I'm having issue with C1111-8PWE with integrated ISR-AP1100AC-E controller/wifi module. While I can easily upgrade router itself to latest IOSXE 17.15.x, I can't find ANY way to upgrade internal controller. How to do that? All methods - from ...
Hello community, A cisco CW-9166I-ROW has been delivered to me to do the configuration for site survey mode, this it to allow the manipulation of the radios (2.4GHz, 5GHz and 6GHz). For that purpose, I´m using a vWLC with IOS AP version 17.9.4 for ...
Hi ,I was reading the documentation about CoA ( https://documentation.meraki.com/MR/Encryption_and_Authentication/Change_of_Authorization_with_RADIUS_(CoA)_on_MR_Access_Points#Enable_Cisco_ISE ) Roaming with CoAThere are a number of advantages to CoA...
Hi , Anyone can tell me Shall I configured Cisco 9136 I AP in standalone mode and act as WLC. Please let us know. Thanks for your support & cooperation in advance.
Just a query has anyone applied for the license through offcom and actively using this on the meraki portal?https://www.ofcom.org.uk/spectrum/radio-equipment/fixed-wireless-accessIs there anyway to mark that you have this license and plan to use this...
