Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi all, I have an issue with my Cisco 9115AXI EWC where I can't access via WebUI. I have enable the http and http-secure server as well but failed.I have saw the traffic that pass through the firewall (Palo Alto), it shows that the application incom...
i have 2 WLC AIR-CT5508-50-K9 AND AIR-CT5508-25-K9 Release: 8.5.151.0 o Type of Vulnerability: SSH Bruteforceo SSH bruteforce login attempts have been detected.o One or more valid SSH user logins have been found through bruteforcing.o Accounts w...
Resolved! Mesh security
I'm researching how to build a mesh securely, and some pages of Cisco itself puzzle me. Configure Mesh on Catalyst 9800 Wireless LAN Controllers - Cisco is one of the latest guides. It shows how to use local authentication and EAP-FAST on the control...
1. Site Survey mode on Cisco Catalyst Wi-Fi 6E access points how to go back to capwap mode2. What is the function of URWB mode?Please explain to me
My AP device has this problem of constantly booting up. Meraki Mode Selected ubi0: attaching mtd1ubi0: scanning is finishedubi0: attached mtd1 (name "mtd=0", size 242 MiB)ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytesubi0: min./ma...
I need to update the IOS version of the Catalyst 9800 L-C, at this moment it has this version: Cisco IOS XE Software, Version 17.06.05Cisco IOS Software Bengaluru, C9800 Software C9800_IOSXE-K9, Version 17.6.5, RELEASE SOFTWARE fc2. I need to install...
Hello!Tell me what the problem might be, there is a C9300-24UX-A switch, a "3504 Wireless controller" and a pair of "AIR-AP1832I-R-K9" are connected to it, and one AP is also connected directly to the controller via a PoE port.WLC3504 sees all access...
Hi all;Consider the following scenario:I want to configure Mobility Tunnel between these WLCs (both of them are 9800-CL with IOS-XE 17.12.4). As you can see below, both controllers can ping each other without any problem:Form the configuration point ...
Hi community,I'm trying to get an USC5310 working on a AP C3600 (AIR-CAP3602I-E-K9). I set up the AP C3600 as stand-alone using software AP3G2-K9W7-M version 15.2(4)JA1.Unfortunately, when booting it reports "Unknown Expansion Detected, please config...
Hi, has anyone had the chance to play with "AI-Enhanced RRM" in Cisco Catalyst Center ? What has been your experience ? We have quite a few RF profiles and wonder if the cloud-based RRM really does a good job so we can lean back and stop using our ow...
Resolved! Recovery image for Aironet 1815i
Hello: We want to add some 1815i APs to an old WLC deployment. We're only able to find new 1815i autonomous (K9) but we need lightweight ones 1815i (K9C). We know that we can use the recovery image for convert autonomous to capwap, but in the drivers...
Hello, I can't find the Power adaptor AIR-PWRADPT-RGD2 in the CCW, any update and which part number to use for access point C9124AXE-ROW
I have accidently removed partition 1 & 2 during the uboot.Now the AP boot loop with below.____ _/ ___|(_) ___ ___ ___| | | |/ __| / __|/ _ \| |___ | |\__ \| (__| (_) |\____||_||___/ \___|\___/_ _ ____ _| | | | | __ ) ___ ___ | |_| | | |___| _ \ / _ ...
I'm using a few Cisco Aironet 1142 ap's in my house configured with autonomous images.The firmware version I have is c1140-k9w7-xx.153-3.JD17.The problem I am running into is there is nothing at all under Network Interfaces on 3 of these ap's.One sho...
In a Cisco Catalyst Controller 9800 SSO deployment, will failover occur if the interface or port-channel of the active WLC is physically shut down?
