Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
We have a guest network setup on WLC 9800-40 version 17.12.2 with ISE (3.1)as radius server. Central web auth is configured with self registered user. Captive portal loads fine and registration of new user is fine.However after login with credentials...
Hello,Is there an easier way to view how many GB a client has used on a 9120 setup (embedded wireless controller)? On my old AP2802 (Mobility Express), the dashboard showed usage data for each client directly on the front page.With the 9120 setup, I ...
we have 2 wlc, 9800 & 3504.a wlan is deployed with same configuation from both wlc to 2 buildings.wlan using 802.1x authentication by same nac.user move from building a to b will suffer wifi connection failure at first several minutes.nac got no auth...
Cisco 9800 Client session data realtime (8540s had enhanced traps)is there a way on the 9800s to gather realtime client session data when deauth trap (i dont see it working when enabled in the snmp wireless traps section.)8540s had this (but i cant f...
I have a virtual wlc C9800-CL, I can access it via SSH and HTTPS from WAN, however when I am on-site connected to the wireless and trying perform a SSH/HTTPS the WLC is not responding. I did a wireshark capture on the WLC, and I notice the TCP SYN pa...
Hi Everyone, I have three cisco AIR-AP2702I-UXK9 model access points. None of them are responding to the console access.Same console cable works for 3750 switch and other routers but when connected to the access point they just dont respond. Just for...
Resolved! C9130AXI_E stuck downloading image
WLC 9800-40Software 17.9.2Hello, we have a problem with ap's not joing the controller.Tried a factory reset, and we log the following:Any suggestions ?[*02/10/2023 11:04:27.9330] Reset chip in progess, not resetting[*02/10/2023 11:04:28.0865] DOT11_T...
Hi,We’re using Cisco Air-AP1815i-I-K9 access points, which are connected to our network and managed by a controller of the same model. We’ve configured the RADIUS parameters in the WLAN (SSID) settings, and when testing the controller with our Micros...
Hi all, I have an issue with my Cisco 9115AXI EWC where I can't access via WebUI. I have enable the http and http-secure server as well but failed.I have saw the traffic that pass through the firewall (Palo Alto), it shows that the application incom...
i have 2 WLC AIR-CT5508-50-K9 AND AIR-CT5508-25-K9 Release: 8.5.151.0 o Type of Vulnerability: SSH Bruteforceo SSH bruteforce login attempts have been detected.o One or more valid SSH user logins have been found through bruteforcing.o Accounts w...
Resolved! Mesh security
I'm researching how to build a mesh securely, and some pages of Cisco itself puzzle me. Configure Mesh on Catalyst 9800 Wireless LAN Controllers - Cisco is one of the latest guides. It shows how to use local authentication and EAP-FAST on the control...
1. Site Survey mode on Cisco Catalyst Wi-Fi 6E access points how to go back to capwap mode2. What is the function of URWB mode?Please explain to me
My AP device has this problem of constantly booting up. Meraki Mode Selected ubi0: attaching mtd1ubi0: scanning is finishedubi0: attached mtd1 (name "mtd=0", size 242 MiB)ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytesubi0: min./ma...
I need to update the IOS version of the Catalyst 9800 L-C, at this moment it has this version: Cisco IOS XE Software, Version 17.06.05Cisco IOS Software Bengaluru, C9800 Software C9800_IOSXE-K9, Version 17.6.5, RELEASE SOFTWARE fc2. I need to install...
