Dear Experts Community,I need you advice on the designWe have 2 x 9800 WLCs working in SSO mode with 400 WAPs and all SSIDs are configured with centrally switched mode.We have 1 LAG connected to Core Switches on trunk port for corporate data and voic...
Forum Posts
Hello Cisco Community,Is it possible de configure the "C9120AXI-EWC-E" as a ROOT-AP (RAP / Mesh controler) ? My previous configuration was :2 AP1231 (Aronet 1200 series) linked together in WORKGROUP BRIDGE Mode >N°1 was a AP1231 in "WGB root with...
Hardware:WLC 9800-CL on Hyper-V - 17.9.3 Cuppertinoc9210i API'm trying to setup an SSID with WPA3 Personal security only but I'm running into a weird issue with both Windows 10 and Windows 11 (My Pixel5 doesn't seem to care)If I configure the SSID wi...
Buenas tardes,Tengo una Mesh con AP IW-6300 con 2 controladoras C9800 por HA (Conectadas con el puerto RP entre si)Aguardo que las WLC esten sincronizadas (una como Active y Standby). Entonces procedo a apagar la activa, toma el control la Stanby, pe...
Hello,I have 3 CBW 150AX, all run fine.However, when I log in to the Primary AP dashboard, I do not see the list of APs under Monitoring->Network Summary->Access Points.The following describes the situation:When I go to Monitoring->Network Summary, I...
Can a C9100 series AP running Embedded Wireless Controller firmware connect function as a lightweight AP under a separate controllerWe might be getting a few thousand Acces points that we would needed to factory reset so we can sell them along but to...
I changed the EWC to CAPWAP: #ap-type capwap So it is now working in CAPWAP mode. However, in the show version, the AP Image type is EWC-AP IMAGE How do I change the EWC AP Image type? APA4B4.392C.F364#sh ver cisco C9120AXI-K ARMv8 Processor rev 0 (v...
HelloWe plan to use Aeroscout Asset Tracking System for a big mall that use cisco wireless infrastructure (WLC 8540, AP 2802, MSE 3365 CMX10, Prime Infra 3.2). I have below questions and would appreciate any help.1- Can we integrate Aeroscout Systems...
Resolved! Cisco AP not registering with controller
Hello,I have configured a Cisco 2504 WLC in my home lab. I have a WLAN configured and connect the AP to the switch. The Cisco AP joins the controller, and I can see it, but it does not broadcast the SSID, and the AP blinks Blue, red, and Green.Cisco ...
Hi ,I have about 20 Aps connected to a cisco Wireless controller 2500 series and they have been working fine.We have a new ERP system coming operational soon and one of the requirements is to have a mesh wifi for handheld scanner.Can anyone please he...
Resolved! SSL Cert using weak hashing
We're trying to solve some vulnerabilities seen on WLC 5520, it's default cert is using SHA-1 WITH RSA ENCRYPTION and it's hashes is considered to be weak. I'm trying to find ways to solve this without needing for a third party CA approval. Will this...
HIIn packet tracer 1.1.6 cellphone not tethering to pcI have followed all instructions, but the last part is not tethering to cellphone to pc.Please see attached text file for instructions.Thank you.S
Hello, I need to Tshoot an incident on a wlc 9800. How do you read .bin.gz files without going through the TAC? Thanks,
Hi, Facing a weird problem. Even with no client connected channel utilization on 2.4 GHZ remains high. Today there were like 5 or 6 clients connected to an AP and its utilization on 2.4 GHZ was 87percent. I have already set the data rate minimu...
We are facing a problem with time zone. When we connect our laptop to Wifi, some apps transmit different information regarding time zone. We are using 24 APs in the network out of which only 7 APs have this issue.AP we are using: Cisco CAP3702I-AFirm...
