Hi all, I'm sort of stumped with our PTP configuration and looking for some advice. We're using a Microsemi TP5000 Time Server as our dedicated GM, which references GNSS for its time. It's configured to use the g8265.1 unicast profile on domain 10,...
Good Day! We terminate PPPoE sessions on A9K-4T16GE-SE line card. We apply pQoS service for each PPPoE session. RP/0/RSP0/CPU0:mskl05#show policy-map applied interface TenGigE0/2/0/16.4001.pppoe4228 Wed Jul 25 08:57:13.220 UTC Input policy-map ...
Hi Hero’s We receive an brand new ASR9904, so I would like to download the Software “Individually-Installable Optional Packages” on the cisco download website (CCO), but I just can find the “normal” 32-bit files. Where can I get the 64-bit packages...
Hello,I would appreciate if you could help me with IOS XR snmp.I have a problem with BGP4-MIB, for example i need to know BGP peers addreses - bgpPeerRemoteAddr .1.3.6.1.2.1.15.3.1.7. But i see only neighbors wich are in global routing table. If BGP ...
Hi All, I am trying to find out the mac address which are getting learned through l2vpn configured. Its a point to multipoint configuration. When I try to ran the below command, it asked for location but I am not sure in which location BVI's are de...
Hi. I have looked up and down on CCO and the supportforums to try and find some explicit definitions for each of the states for the DHCP proxy state machine, but have been unsuccessful. Or are you able to provide this or point me in the right direc...
How can I change the SSH default port(22) in ASR 9K? I heard ASR9K can't change SSH port.. is this right?? Could you reply related document link to me?
Dear Community Hope everything is going well. Today I installed a new Modular Line Card on a ASR 9010. I followed the the isntruction on Cisco documentation but I got the following error messages and the MLC remains in the shutdown state. RP/0/RSP1...
Is it really not possible to police control-plane traffic to local device, that is otherwise be subject to the LPTS please? The problems with LPTS is that its policers are only on aggregated per LC per NPU per protocol bases, I’m missing the per inte...
Hi,I'm running IOS XRv in VMware Workstation. I have a simple topology of two PE routers connected to a P router, all running XRv.I have configured Layer 3 VPN's and layer 2 Local E-Line VPN's (AC's on same PE) between the PEs with no problem. But wh...
Hi member, I'm working with an ASR9006 router iosxr 4.3.4 and I get the bgp routes below and I see it preferring path 3 instead of path 1, by default route selection criteria bgp path 1 should be the best, correct? , I do not know if I need to cha...
Hi, how to check the cpu history for last 72 hours in ASR 9K.
Hi, We have a couple of Cisco ASR 9006's which we are looking at upgrading to 6.2.3, Can we directly upgrade from 5.3.3 (32bit) to 6.2.3 (32bit)? Looking at the upgrade documentation it suggests their might be a need to install bridge SMUs before...
We are running a textbook MPLS VPN using EIGRP as the IGP on ASR 9006s running a mix of IOS XR 6.2.3 and 5.3.4. Before Non-Stop Routing (NSR) was enabled for LDP we experienced a 60+ second outage on VPN traffic when performing a 'redundancy switch...
# sho bfd ipv6 session detail SpoilerI/f: Bundle-Ether1.751, Location: 0/0/CPU0Dest: 2001:b1:fe0:5::1Src: 2001:b1:fe0:5:: State: DOWN for 0d:0h:21m:25s, number of times UP: 0 Session type: SW/V6/SH/BLReceived parameters: Version: 0, desired tx inte...
