Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Cannot access vmanager on GUI
by harikrishnanaidu749 -
Where to find cheap ISR ?
by -
Cisco SMA resources allocation
by ahmedFawzy -
ASA in Active/Standby Mode connected to ACI
by Ibrahim Jamil -
Cisco secure firewall 1200 series
by -
802.1X auth fails certs missing CN
by thenetadmin -
VXLAN BGP EVPN Default Route
by uni1389
Community Activity
Where to find cheap ISR ?
Hi I am a looking to get into old ISR Cisco module for a tftp server and also to use it for connecting my Cisco ip phones I got at a recycling store any ideas on where to get like Cisco 2800 series or similar machines in India for cheap??
Cannot access vmanager on GUI
Vmange(config)# do show running-configsystemhost-name Vmangesystem-ip 1.1.1.1site-id 100admin-tech-on-failureorganization-name airtelclock timezone Asia/Kolkatavbond 100.1.1.3aaaauth-order local radius tacacsusergroup basictask system read writetask ...
Cannot access vmanager on GUI
Hi. I am new to SDWAN and am trying a basic lab. I have attached my lab topology. I implemented this on eve-ng using vmware workstation player 17.. After installation and basic IP configuration on vmanager and winserver I can ping vmanage IP (192.168...
Two VPNs at the same time
I’m trying to access my desktop remotely through a VPN I set up on my router. However, I also need to use the Cisco VPN for school in order to access certain software. Ideally, I’d like to have both VPNs active at the same time. While they technicall...
ISE 1.4 not work
Hello.We're using ISE 1.4.0.253. Recently, the web interface on the master virtual machine crashed, and there were errors in the switch logs.We checked the status, and everything was bad:sh application status ise ISE PROCESS NAME ...
802.1X auth fails certs missing CN
Hi FolksWe’ve recently started seeing a random issue on about 10 endpoints where both wireless and wired 802.1X authentication failsCurrent setup:Wireless: User + Machine authenticationWired: Machine authentication onlyAuthentication method: EAP-TLSC...
Cisco SMA resources allocation
Hello, I already assigned lower specification for virtual cisco SMA on Microsoft hypervisor. i need to assign higher resources for the SMA. what is the best practice steps to this.
VXLAN BGP EVPN Default Route
Hello all, On Border Edges(DC01-BE001-6/7) am trying to advertise default route from GRT to MPBGP-EVPN but not able to do it properly with the following configruration. Thanks in advance for tips and correction **************************************...
ACI with DMZ Servers
Hello Freindswith Regards to ACI with DMZ Servers can we provision the DMZ Servers (Web-DNS-Mail) directly on the ACI Fabric in Main Tenant aka(Production Tenant) instead of having Dedicated Tenant for DMZ Servicewe Already have PaloAlto at Internet ...
ASA in Active/Standby Mode connected to ACI
Hello Freindsfor ASA in Active/Standby Mode connected to ACI , do i need 1 IPG(vPC) For Both or Just 2 IPG 1 for each device? I know 1 IPG for both ASAs if they are in Cluster Mode but confused in Active/Standbythanks all
5440 Endpoint abandonded EAP session and started new
Hi All,Recently, we migrated our enterprise Wi-Fi authentication method from PEAP to TEAP (inner auth EAP-TLS). Since then, many users have been experiencing disconnections while their sessions are active.In the morning, the Wi-Fi connects and works ...
Cisco secure firewall 1200 series
I cannot find anywhere if the local admin account for FDM has a break class in any documentation. If say the account has been compromised. Can we console into the cli to reset the pw or do we have to reimage firepower and reload the configs?
DNA server CrashLoopBackOff error
I have 3 DNAC server nodes. I finalized the conf for the 3 and created the H, A, but after I turn off the devices and turn them on, the attached log error message appears for me using maglev most of them (CrashLoopBackOff)ndp pipelineruntime-taskmgr-...
Nexus 5672UP – Ethernet Ports Not Visible After Slot Reset
I have a Cisco Nexus 5672UP switch running NX‑OS 7.3(6)N1(1). The switch was functioning normally, but after performing a reset, the Ethernet ports on Slot 1 (ports 1‑48) are no longer visible in show interface status or show interface brief.
