We have 2 ACI fabrics, one for prod and for test. We have a Checkpoint VSX running R80.20 and I am sure that we had the prod apic connected to CP. We have made an datacenter object which is the apic in the CP, and click test connection. This faile...
Forum Posts
Resolved! Does ACI fabric support native FC?
Nexus 93180YC-FX has the support for FCoE and Native FC and specsheet also shows it can be used as a Leaf switch. So does ACI support native FC now? Second question, I remember there are radio buttons on APIC GUI for selecting "ethernet" or "fc" bu...
Is it possible to disable/delete/lock the default admin user account on APIC by another account with the same privileges? I tried doing so and I got this error:
I'm trying to understand how AVE VM two interfacesave-internal-1ave-internal-2VM adapters mapped to one single KNI interface(kni1) ? It looks like kni1 takes the MAC address of ave-internal-1. what happens to ave-internal-2 VM adapter? I don't see it...
Hello, I'm using the ACI version 4.1 and I can't find the create multi-pod menu where we used to create multi-pod in previous ACI versions.I've uploaded a screenshot of my APIC with the menu create multi-pod missing. I could create a pod but can't cr...
Resolved! Routing Policy in L3OUT
Hello All - Can anybody help me understand the difference between "Match Prefix AND Routing Policy" and "Match Routing Policy Only". This option you can find here: "External Routed Network"-->L3OUT-->"Route Maps/Profiles"-->"default export" On what c...
Hi I have a fairly new installation at a client running in Multi-POD. They are running version 4.1 but since we started to configure and migrate servers we get exceptionally slow responses from APIC. In many cases we receive response errors on both ...
Resolved! Spine/leaf cabling rules
Is it possible to add a new spine into the existing fabric even if the spine is not conected to all leaves? I know this is not a valid design but I'd like to know if this works. Is there a document which describes ACI behaviour when some cables are n...
Resolved! HELP! ACI LLDP ISSUE (VM Discovery)
Hi everyone,So we're currently in the DC traditional network -> ACI transition and stuck at somewhere with the VMs provisioned on Vcenter/ACI.Since we've hired contractors to help us with the migration, we've run into a situation where we're complete...
Hi, leaf 93108 won't boot as leaf (ACI mode).It remains in loader> mode.If i try to boot image from USB, It fails again. This is the error messages:loader > rebootCISCO SWITCH Ver7.65Device detected on 0:1:2 after 0 msecsDevice detected on 0:1:1 a...
How can we connect the ACI VM Simulator to an external L3/L2 devices? with EIGRP/OSPF routing protocols. Thanks.
Hi All, We are connecting a Firewall and Router to the ACI service leafs (topology attached), and in order to exchange routes between the Firewall and the Router we are going to run the OSPF between them using the ACI Fabric as a broadcast L2 domain ...
Hi,I have two similar problems on two ACI Fabrics, both are lab kits with a single APIC each.Problem #1After upgrading from v4.0(1a) to v4.1(2g) and completely clearing the config (acidiag touch setup, acidiag touch clean, acidiag reboot), all the AP...
Hello, After reading cisco materails and do some labbing for EPGs to BDs mapping, i came here to know the below queries which actually confused me. 1-Two EPGs bind to one BD on single Leaf (Using same encap vlan) 2-Two EPGs bind to two different...
Resolved! "Advertised Externally" in BD vs EPG
Hello All - Configuring L3-OUT, so I have two questions. Can you help me, please 1) I wanted to advertise BD subnet to External Router using L3OUT, typically we enable "Advertised Externally" option under BD. I learned in one of the Cisco session is,...
