Hi,Just read there is new integration available with NSX-T SDN controller from ACI version 5.1.Cisco ACI and VMware NSX-T Data Center Integration - CiscoBesides this there is not a lot of information available for this. Is there any good reference a...
Forum Posts
Resolved! modelete, mocreate still supported?
Hi board,I'm quite unsure regarding the "modelete" or "mocreate" operations in the APIC bash. I'm running ACI 4.2 and as soon as I run one of those commands, I get the message:This command is being deprecated on APIC controller, please use NXOS-style...
Primary question - What is the difference between the subnet defined under either the uEPG or the AP EPG vs the subnet defined on the Bridge Domain associated with that uEPG/EPG?Secondary question - Do you need (is it common/best practice) to only se...
Resolved! Ping from APIC command
Hi all, I need to find out if an IP is used or not in a particular BD, for doing this I need to ping some unused/free IPs (emerged from show endpoints) in order to know if there are some "sleeping" hosts or if I can really use those IPs. For doing t...
I was thinking if we can automate a vPCs to enable/disable based on a trigger. For Example, I have 4 ports under 2 vPCvPC no.1Leaf_101: Eth1/1Leaf_102: Eth1/1vPC no.2Leaf_101: Eth1/2Leaf_102: Eth1/2 But at one single time one of the vPCs should stay ...
Hi,Can anyone answer with regards to fiber link connectivity between spine and leaf?First Question:Is it mandatory to have all the links between these devices to be at same speed? I mean if I connect a leaf switch to one spine at 40G and to another s...
Hi all,Just wondering....Is there a sane reason why node numbers in ACI max out at the number 4000?Now I understand working with processors where every bit counts (yes, I did write machine code for the 8 bit Z80 at one time in my life)But last time I...
Hi experts,I always like a picture!As the picture shows, there is a VPC configured between leaves 2201 and 2202.There is continuous traffic flowing between all four servers.But my question is, why doesn't Leaf2201 see the webserverbm (10.218.12.10) a...
Hello Experts , I am trying to trace the endpoint 10.10.10.18 from source connected leaf switch .From the below output I can see to reach 10.10.10.18 we have to go via tunnel23 ...How do I check next from cli ? what is the command to check the tunn...
Hi folks,OK. I know I can run the following command agains a leaf to find the Spine anycast proxy addresses,apic1# fabric 2202 show isis dteps vrf overlay-1 ---------------------------------------------------------------- Node 2202 (Leaf2202) ------...
Hi,Recently some ACI Leaf-Switches did a reset reason: reset-triggered-due-to-ha-policy-of-resetService: epm hap resetVersion: 14.2(2f)Hardware: N9K-C93180LC-EXI cant understand why this is happening
Resolved! Lot of ActiveUserSession Events
I have reviewed the Events and Audit Logs and in the Events tab I found a lot of records like this : uni/usersessext/delsession-oKX0GAPrTV6IJZzVIhOEaQ==Createduni/usersessext/actsession-4j9PF3KyRViDkqcXR4Lf_w==Deleted I have more than 100 pages with ...
Hello All, I have a home lab and decided to add an ACI environment since I am studying for CCIE DC.Got APIC-M3 appliances, one spine, and two leaves.unfortunately, I did not know this caused an issue and did a dumb thing and installed ESXi on my APIC...
Resolved! moquery -c fvRsCEpToPathEp
Hi Everyone, I am currently working on a small project in which i have to delete alot of unused static ports. Now as i was going about i was wondering how i would know which port is being used and which isnt.. so i figured out that i could moquery fv...
Hi everyone,We have some issues with our ACI connection between 2 POD. The 2 EPGs between 2 BD on the same VRF that are located between 2 POD can't access each other. BDVLANxxx: EPGVLANxxx : POD1 : DCBDVLANyyy : EPGVLANyyy : POD2 : DRCWe are using ...
