I am in the process of Migration all servers from our Content switch to CIsco ACE4710.one content has this line itemadvanced-balance sticky-srcipWhat would be similar option in ACE.?Thanks for any help on this.Mehdi
Hi there , I have WAVE 574 (not central manager ) running Version 4.2.1 . I suppose to upgrade the version to 4.4.5 . Is that comaptible ? or anything else i need to care about ??Thanks & Regards,Ram
Hey,I have a requirement to load balance OWA 2010 inbound connectivity to 2 CAS servers using a ACE 4710 with sticky sessions enabled.The CAS servers are currently responding on 80 or 443 at this moment in time. Eventually I want to off load the SSL ...
Hi Does anyone know what the maximum acceptable latency is on a FT Link between a Pair of ACE30 modules configured as a FT Pair with multiple contexts running active/active.I am trying to ascertain if it is possible to site in different DC's seperate...
Hi.We have an ACE30 (running A5(1.2)) and a couple of Exchange 2010 CAS.We have little experience in load-balancing, but we found this guide from Cisco: http://www.cisco.com/en/US/docs/solutions/Enterprise/Data_Center/App_Networking/Exchange_VSphere_...
Configured ACE in routed mode ,and have the vlan ,route-map defined on th switch.Able to ping the server vlan ,and servers from the ACE ,but unable to ping the vip from ACE ,but able to ping the gateway for the client vlan.Attaching the config the of...
Hi all,i have a query on layer 3 load balancing. Please refer to the following example and config,service Aip address 1.1.1.1keepalive icmpactiveservice Bip address 1.1.1.2keepalive icmpactivecontent Cvip 10.10.10.10add service Aadd service BNow for ...
I can not find any information on the cluster licence for WAAS Mobile. I assume this is needed if you want to run redundant servers. Or how you orderCan anybody supply a good link, or explain what I need?CheersAndy
Hi guysToday I got a customer that installed a WAE device on its LAN environment.Basically, they engineering team, for some reason, did not allow to be directly connected to our router so we have the WAE device on a different vlan from the router sub...
Dear fellows,I have the following enviroment:2 6500 Core Switch2 ACE10-6500-K9 installed in 2 Core Switch3 context > AE,CE,PE6 SERVERS -> 2 servers for AE Context, 2 Server for CE Context, 2 Servers for PE ContextDefault Round Robin Load Balancing fo...
Hi Community,I'm deploying a Cisco ACE module and I have some questions about sticky connections and about the output of the show conn command and show serverfarm command.I have the follwoing configuration:rserver host srv_1 ip address 10.4.11.14 i...
HI EveryoneIn need of some help in understanding how/where the numbers come from when looking at the how the reduction ratio is calculated.In an example I can see the following: Original Optimized ...
Dear all,I am new to Cisco WAAS and therefore I would like to request some help regarding the following scenario:I have a star network (1 hub and 5 spoke) topology where each satellite site is connected via a 2 MB (symmetric) to the Head-Quarters (...
Added new remote site today utilizing a WAVE274 appliance as the site only has three T1s. I'm using WCCP to redirect traffic to the appliance and wccp indicates that the appliance and router are communicating properly. The appliance resides on a di...
Hello,I created several rules to balance on a specific server somes apps. Everythings works great in http but no in https.In my example, i would like https://www.app2.com/ to be redirected to my server2 but it's always using the default rules instead...
