Application Networking

I am looking at deploying 2 x CSS11503 (inline redundant) in an environment where it may have to statically route for a large number of hosts. The largest network any interface is directly connected to is a /24, but static routes on the CSS may be n...

Does anyone know what these errors mean?DEC 16 14:43:53 css-1 3/1 1 IPV4-2: Ipv4SlaveForwBmanChk: no ingress LP in bufferDEC 16 14:43:58 css-1 3/1 2 IPV4-2: Ipv4SlaveForwBmanChk: no ingress LP in bufferDEC 16 14:44:03 css-1 3/1 3 IPV4-2: Ipv4SlaveFor...

Hi, I've got a simple WCCPv2 config between my 6500 and 7325. I see redirects occuring to the CE but when I browse on the CE to my savings page, all I see are misses and 0% savings. My client just keeps refreshing the same page but still the CE does...

Hi,I'm quiet new with CSS configurations and currently working on an assignment to get two servers (with both a redundant network connection) connected directly to a redundant CSS configuration. I have tried a box-to-box redundancy configuration but ...

Hi All,I was aked to look into the possibility of using a pair of 11503 CSS to provide load balancing to a pair web servers hosted on a IBM blade server. These blade servers are connected to Layer2/3 switch with routed links to the distribution layer...

On my syslog was an error message.DEC 14 09:17:03 1/1 168 IPV4-4: Ipv4MasterProcessArpFrame: bad ARP packet receivedTried to run through the error message utility but got no output.Can anyone explain exactly what this message is telling me?Thanks in ...

hi,I have two named keepalive config. and both of them exactly the same except port number. Such as:keepalive SPDA_Transcoding_80 port 80 ip address 10.X.Y.49 uri "/KeepAlive.bin" type http active and keepalive SPDA_Transcoding_81 port 81...

We're testing Smartfilter and now we're trying to get transparent http authentication to work with it. We can get authentication working, just not transparently. We're testing smartfilter 4.0 server with the authentication piece loaded. We're on a...

I have a new CE510 that when booting displays memory ok, press F1 for setup, then processor and IDE drive info and then the screen goes blank with the cursor in the upper left corner. Nothing else. Even if I try F1 for setup or F12 for Boot Menu I'...

A colleague of mine is setting up a new CSS. When he enters the ODM there is not an option to book from disk, only Network, Ftp and Clear ? Is there a reason for this, the documentation I read suggest the 'boot from disk' option should be there. Than...

I would like a way to do this without changing the application. Below I found one way to do this in this forum but can one do this? I didn't see a way in the css scripting language to check for the ICMP error.Is it possible to write such CSS script:...

Due to the configuration on the company. They use 2 IP address. Joining 2 networks 192.168.7 and 192.168.1 so that the 192.168.7.*** can use one of the other systems.Thank You, James Loebs

Hi,We would like to move a tcp connection (not http) between host 1 and server 1 to host 1 and server 2 when server 1 has to be go under maintenance. A CSS would be used.If we put the server 1 in "out of service" mode, all new connections go to serve...

We have IIS version 6, and we are installing new CSS11503 with SSL module, we are trying to import the certificate na dthe key from the IIS6 to the CSS, we followed Cisco steps, but the IIS6 have one file that has both the certificate and the key, an...

Telnet is enabled,yet it refuses conncetion and shows no active connections via the console.This is a 11051 chassis running 5.x software I believe. Console access works fine. Another interesting point is I can ping the box only once! then it fails af...