Hi all,I used Intune to upgrade Cisco Secure Client to the newest possible version (5.1.2.42) - 86 are installed. I have problem only on 2 devices - so that's not InTune fail.I'm using this msi file: cisco-secure-client-win-5.1.2.42-core-vpn-predeplo...
Forum Posts
Hello,Working with the Cisco Catalyst Center version 2.3.7.4-75326When I try to run API queries within the CCC web interface or from the exterior, I get unexpected results 404 from all the PnP commands but not the others categories.Example with "get ...
I have this problem where my email server doesnt work, i am a student learning networking and would love for a detailed explaination to this problem and why its not working.
Excuse the terrible title. My question is if a Switch has two data VLANs (Accounting/Marketing) and it maintains a MAC Address Table, When a switch receives traffic from an end user device connected to the switch and the device its trying to send tra...
I'm a contractor for the DoD. I work from home. I have a government laptop (Dell Latitude 5420, running Windows 10 Enterprise, version 20H2). I am running AnyConnect Secure Mobility Client version 4.10.07061. I cannot change any AnyConnect Secure Mob...
Good day, I am using CML 2.6.1, have a simple topology built, with two hosts, and a single Nexus 9K device. Both hosts are connected to the device. The configurations are default, except the following:- There are 2 vlans on the nexus, vlan 2 and vlan...
Hi there, I have Cisco 9300-48T switch keeps on Rebooting after upgrading from 16.9.3 to 17.9.5. The error shows, failed to allocate space for the ISO (out of Resources)Boot: failed to boot file flash:cat9k_iosxe.17.09.05.spa.bin (Out of Resources)Pl...
Hello everyone, we are upgrading SSM on prem satellite from 8-202308 to 8-202401 but we are getting the following error: >> upgrade patches:SSM_On-Prem-8-202401_upgrade.sh Upgrading system from patch file ... /var/files/patches/SSM_On-Prem-8-2024...
i have cisco 93180 and i am planning to upgrade IOS to nxos.9.3.9.bin.i have connected USB drive and switch has recognized it already but when trying to copy IOS from USB1: to BoolFlash: it get the following error message.file error Destination: Read...
A question more so then anything else, I've searched through the forums and not yet found the answer.About to upgrade a ASR920, checked the upgrade manual available which specified the following:"If the ROMMON version is 15.6(24r)S and the Cisco IOS ...
Good day,Im new to packet tracer and i just don't understand why it doesn't work it gives me SMTP authentification error yet i've literally copy pasted the user and password, if i press receive it works but sending doesn't. Use the PC's ive encircled...
We are building a B2B ipsec vpn tunnel with a customer who are using cisco meraki as their vpn device. In the past I remember that we had issues with meraki regarding NAT. What we need, is for customer source nat their internal ip's (ex. 192.168.1.0/...
I'm trying to order some core and access level C9000 series switches to replace the old ones in our campus .Considering we will be continuing to only use traditional features designed , I'm trying to figure out :Is it feasible to only order the Netwo...
Error: 400 - Validation failed: Port: topology/pod-1/paths-107/pathep-[eth1/28] has more than 1 native encap
Hello all, I ran "Factory-Reset all" on our Catalyst 9200L 48P mistakenly thinking that would reset the configs on the Switch. I've booted up the bin file via usbflash0 on the ROMMON menu, but once I'm on the switch and attempt to copy the bin file t...
