07-02-2019 12:06 AM
Hi All,
We have a situation that is not a typical call centre but is using UCCX and performs most of what we need well. There are a couple of things we have noticed that I would like to see if there are workarounds (I have created these as separate discussion items)
Call Order
The following example is when one agent is logged in for simplicity.
I do not want to log out the agent and I cannot extend the timeout as this will prevent other people from picking it up when available.
Thanks,
Paul
07-02-2019 01:34 AM
As the CSQ works in FIFO mode, when your first call is not answered and goes back to queue, it is put behind second call, which is working as designed. However you can overcome this by increasing call priority of first call by Set Priority Step when first call was not answered by an agent. This will put first call back in the first place of the queue by referring to its priority over second call.
I hope this will be helpful.
07-02-2019 08:27 AM
07-04-2019 06:40 PM
Thanks Piyush,
I shall have a look at priorities and see if this will do what I need and let you know.
Regards,
Paul
07-02-2019 08:30 AM
07-04-2019 06:47 PM
Hi Anthony,
Thanks for your help. Please see attached script. Forward no answer is set to 12 seconds.
Regards,
Paul
07-05-2019 01:57 PM
When a CCX queue call to an agent is answered CCX checks that number that answered the call is the agents. If it's not the agent CCX pulls the call back and put it in back in the queue.
From what I have observed this check and pull back can take a little time, maybe a quarter of a second. It's possible that if a second call is waiting in the queue it may sneak in while CCX is getting the first call back.
As Anthony said make sure your ring no answer timer is greater than the Timeout in the Select Resource step.
You must make sure that nothing else or no one other person can get the agents call. Make sure the agent is not part of a pickup group.
Just like your MOH question the real fix here is to get the agents to answer their phone when it rings.
Graham
07-08-2019 11:34 AM
07-09-2019 10:29 PM
Hi I have modified the CUCM and UCCXs timeout I still get the second call "sneaking through" there appears to be nothing wrong with the servers performance wise. It happens 100% of the time when we have this situation. That being said most of the time we will not have this situation occur as the calls are mostly being answered before this occurs.
Thanks for your help on this
07-09-2019 10:55 PM
You may have already checked this one, but can you please confirm what is the busy trigger configured on agent DNs. It should be - Maximum Number of Calls set to 2 and Busy Trigger set to 1.
07-11-2019 01:14 PM
I ran a test on my lab system
With the "Agent State after Ring no Answer" set to Ready then you are correct. The first two calls in the queue alternate in their presentation to the agent.
With the "Agent State after Ring no Answer" set to Not Ready then it works as expected. After you put the Agent back to Ready in Finesse it is always the oldest call in the queue that is presented.
Do you have "Agent State after Ring no Answer" set to Ready?
Graham
07-30-2019 08:16 PM
Hi Graham,
Apologies for the delay I have been away. The agents are set to remain in ready as they do not want them to have to log in again. I know it is unusual but this is because of the face to face contact this team has as well. I will talk to them again about changing this. Thank you so much for testing this and confirming that it is working as what we are seeing.
Regards,
Paul
07-31-2019 08:44 PM
07-30-2019 08:12 PM
Thanks Piyush, Yes they are set this way.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide