MPLS

Hi,I am setting the dscp for MPLS network QoS.However the packets were not marked although clas-map and policy-map has been defined.When I start ftp transfer,basically to generate ftp traffic,all packets goes to class-default.Attached is the config a...

I connected Cisco3640 to IXIA,and sending RSVP messages from IXIA but geting the following error.*Apr 11 06:55:49.974: %RSVP-3-BAD_RSVP_MSG_RCVD_TYPE: RSVP Message had a bad type: 20-Traceback= 0x603F4E74 0x60B61928 0x60B709A4 0x60B5854C 0x60B58AEC 0...

Hi,I can see a router (Cisco) propogating MED value to ebgp neighbor (ERX Juniper) but cannot see MED value in ERX..I used this command to see if Cisco advertises MED CISCO#sh ip bgp vpnv4 vrf XXXX neighbor ERX_IP advertised-routeI can see the MED va...

Hello group, Recenlty I'm having some problem in my production PE routers. At times, the PE is not generating any MPLS VPN tag. When this happens, a syslog comes saying: "Jun 30 10:16:16.169: %TFIB-4-FIBCBLK: Missing MPLS Forwarding Information Base ...

Can someone please help answering my following questions:Question 1: what is the max no. of VRFs that can be defined on Cisco 3800 ISR? And how much memory do we need to support the max no. of VRFs on 3800?Question 2: is there any Cisco documentation...

PE7#sh mpls forwarding-table vrf cust1Local Outgoing Prefix Bytes tag Outgoing Next Hoptag tag or VC or Tunnel Id switched interface23 Aggregate 192.168.47.0/30[V] \ 024 Un...

Folks, As per cisco documentation, 12.2(25)SED should support vrf-lite for eigrp. When i download the code and run it on the switch, i do not see the vrf optionEnter configuration commands, one per line. End with CNTL/Z.c-b-2(config)#router ei...

hi,I have setup like.CE4-PE7-P-PE4-CE2..I am able to see all routes from CE4 into the routing table of CE2 and vice-varsa .but i m not able to ping from CE4 to CE2 and Vice-varsa.i m useing PE-CE as RIPv2.what will be the problem

Hello,Has anyone seen "Route Distinguisher 0:0"?I have a setup simulating an Inter-AS L3VPN - Back to Back VRFconfiguration.The problem is that in one of the VRFs, under command "show ip bgp vpnv4vrf VRF_TEST" I see usual routes under the RD configur...

HiWe have two PE nodes connecting to Pnodes with redundant links. The two PE nodes are in remote locations (same City). The cost of the longhaul links are very expensive, so we would like to put a link in place between the two PE nodes to get aroun...

Folks, I keep reading in this forum that in an MPLS network if the MTU is 1500 bytes (default), a lot of packets would get dropped as the labels added to the original packet make it bigger than 1500 bytes(4 bytes per lable). So i did a test tod...

Hi! As you can see from the attach, we are using a topology where 2 7609s act as a PE, and we are also running a LAN (VLAN actually) with 3 HSRP groups in it.Basically, what we have is several VLAN, and each one of them with 3 subnets configured in t...

a quick question,how long does it take for a transit provider to propagate our prefix to the internet so that anybody in the internet has the knowedge of my prefix?One day? 3 days?

Folks, I do not see in the feature navigator that sup720 supports l2tpv3, very surprised? how do service providers running 7600 series router provide Lan services to customers then?the ones who are not running MPLS that is?