We want to use the Catalyst 9500 switch to build a MPLS network, and also want a management system to manage the network. I want to know can we use EPNM to deploy and manage the MPLS L3VPN for Catalyst 9500.
Good Morning! We are using LDAP/S as authentication to our devices. We have it configured on our ASA's and are having difficulty configuring it on the 9300 switch running 16.12.04. Is there a configuration guide to set LDAP/S as the authentication ...
Good Morning, We have an ASA 5545X thats running 9.14(1). I am having a difficult time using scp to copy configs to my laptop. I have the scp server enabled on the ASA and keep getting errors. I am trying to copy running configs from the ASA to my la...
Estimados buenos días, quisiera que me ayuden con este inconveniente.Mi cliente usa CP LMS 4.2.5 y actualmente adquirió equipos 9500 y 9300C9500-12Q16.9.5 CAT9K_IOSXE C9300-24U 16.12.4 CAT9K_IOSXE Y me comenta que no puede ...
Hi Guys, Need to know the difference between "EvalRightToUse" and "Permanent". License Type: EvalRightToUse <<<<<<<<<<<<<<<<<<<<<<<<<<License Level: advipservicesNext reload license Level: advipservices License Level: advipservicesLicense Type: Perm...
Hi, I'm trying to create a template to configure the banner of the Fabric devices using the template editor in DNAC.It is similar like this, <MLTCMD>banner motd ^Banner Line 1Banner Line 2Banner Line N^</MLTCMD> The template saves and commits success...
What happened, the value of this SLA OID would be 16?0:other1:ok2:disconnected3:overThreshold4:timeout5:busy6:notConnected7:dropped8:sequenceError9:verifyError10:applicationSpecific11:dnsServerTimeout12:tcpConnectTimeout13:httpTransactionTimeout14:dn...
All my other phones say 3PCC in the model number. So will these phones work? and if so, how do I clear off the previous companies settings and passcodes? Or do I need to send these back and buy 3PCC phones only?
I encounter something weird.When i try to check if a specific ACL exist with the specific settings i get incorrect successes.i have the followingcondition 1Condition scope: Configration
Block Start Expression: ip access-list standard (.*)
Advance blo...
Good Morning, We are setting up Netflow on our Cisco ISR 4461 to SolarWinds NTA. Our router has isr4400v2-universalk9.16.09.06.SPA.bin. I can handle the Netflow Config, but am having difficulties with the show commands to verify it was installed corr...
Hi All - The Router License shows its end date is tomorrow. What will be the impact if it is not renewed by tomorrow. Will the Router stop working after 30th Nov?It shows the License Type is Permanent. Should i worry for this end date?AWSRTR11#show l...
Hi! I purchased a UCS-FI-6248UP to use in to connect 2 Storage servers with 5 esxi servers via iSCSI. I wanted a 10GB switch to get up the speed. the servers are connected thru twinax cables. i’m a totaly noob on managed switches and have not worked ...
Hello everyone, I would like to secure my router using Netconf with an access-list. Documentation says: netconf-yang ssh {{ipv4 | ipv6 }access-list name access-list-name} | port port-number} But on my router there is no such option: router#netconf-ya...
Hello everybody, I have a RV160W, it is configured as dhcp server, it´s ip is 192.168.1.1 and it assignates ip in that range (192.168.1.xxx)Y have configured a ipsec VPN, client to site type.I can connect to the VPN and as i could not configure the i...
