Hello,I would like to make sure that now Nexus 7K has new feature of IP SLA however how about the supporting for Nexus 55K? [Nexus 7000 Series NX-OS Release Notes, Release 6.1]http://www.cisco.com/en/US/docs/switches/datacenter/sw/...
Hello I use SMTP notification over EEM TCL. All work fine. But I need found way resend email message then WAN channel was down or SMTP server not working.Can it possible?
Hello I have question, can I see message form Switch to Router for activation EEM?I think one way use SMNP for this.On router side i have configuration:event manager applet snmpevent snmp-notification oid 1.3.6.1.4.1.12345.1.0 oid-val "1" op eq maxru...
Dear Freinds I have below requirement I have a Track 111 set whch will monitor IP SLA 555 and set its state Up and Down based on sla status.Now Based on tracking state, the eem applet should trigger 2 scripts. when the track state is down it trigger...
Hi everybody!I've connected my c3560G which I use as Core-switch in my company to Prime Infrastructure 1.3.And sometimes I see a CPU overload over 50% only by SNMP ENGINE process. Total CPU load at this time - up to 100%Possibly, It's happened after ...
Hi, I've launched a NetShow job against several routers. The job result is successful but appears the following message: Deploy successful (TELNET: Failed to establish TELNET connection to 10.253.49.34 - Cause: Authentication failed on device 3 time...
Hello,I have a problem with one slave server in my LMS 3.2.1 environment.There are a lot of threads to the failure "JRM server is down or inaccessible for this user" in this community. But no solution helped for my server.I have three servers running...
Hello,Justed upgraded to CNA 5.8(6), when I try to configure any port's VLAN of one of our old switches (Catalyst 3548-XL IOS 12.0(5)WC17)I am not able to do it anymore. It just shows the error this message :Error: Modify Port Mode com.cisco.cpnm.fea...
We have a customer with an issue with LMS discovery. It will discover new devices but will fail to update them to the DCR, because it does not match the credential set policy when the credential set is defined by Device name and an SNMP OID is used...
Hello Community,Whenever I attempt to run a Tcl script I get the following error message:Tcl policy execute failed: cannot get pty for exec: Error opening vty no more tty linesI inreased the number of vty lines to 10 but every I run the script it tak...
We have LMS 3.x in our network and we want to assess which one is more wise as a decision and more future proof To move to LMS 4.2 version or Cisco Prime Infrastructure?Are CPI current version good enough or we should wait for 2.x to come out.-Thank...
Hi, Just thought I would post a working EEM script on doing a router reload when the L2TP tunnel goes down....I am using a 3825 router to initiate a site-to-site tunnel with a 3rd party vpn service - StrongVPN. On the odd occasion when the tunne...
Have configured DCNM to backup daily the running config starup. After I enabled the feature tacacs + The DCNM stopping backing up. But when I logon as the switch with the User created in tacacs_plus he can log in and run the command privilege 15 on...
Hi All,We have CiscoWorks LMS in our network. While going through the firewall logs, I see that this server is generating heavy ICMP traffic to multiple subnets in the network. I did check the Ping Sweep settings but it is disabled. I cannot understa...
Hello Support,I tried to authenticate the LMS 4.x Users via TACACS+ on ACS 4.1. But unfortunately is not working! On LMS 4.x i have created users and i have defined roles to the users. I have defined the Authentication Mode Setup for TACACS+ on LMS 4...
