Good afternoon! I have an ASA 5505 which is connected to an Active Directory DC for AAA via LDAP. I want to move to LDAPS. I have a local CA that provides the DC with its DC cert (for LDAPS). LDAPS is working fine with several other devices on th...
Hi, One of Our Clients are planning to convert their existing Multi-Context Firewall into a Singel Context ASA. They have a Apex Anyconnect License and is wondering if this License will be usable and compatible to the Single Context One. Apprecia...
Hi, I've got an ASA5505 to study. And i'm trying to download an asdm of this ASA device from https:// There is my configuration : Saved:ASA Version 8.2(5)!hostname ciscoasaenable password 2KFQnbNIdI.2KYOU encryptedpasswd 2KFQnbNIdI.2KYOU encrypte...
hi.I've got a 5520 firewall (well, two, but they're active/passive, so one logical unit) and I've connected the management port to a VLAN in my infrastructure.Which is fine if I access it from within the same subnet - I can access the management port...
Hello,I have bought a cisco asa5516X with control and protection licenses. I want to block "hotspot shield" and I use the firepower module to do it but it doesn't work and hotspot is always working on clients. Someone can help me to do that please?T...
Is it possible to utilize any dynamic IPS | IDS functionality of SourceFire for known malicious IPs and geo-blocking of rogue nation states without the purchase of a dedicated IPS | IDS system. Can I, for example, utilize Brightcloud | Talos to fil...
Hi community, We have a pair of 4150 FTDs being managed by an FMC 1000. As part of our policy configuration we have a default action of deny for any traffic that does not match an allow policy. We also have logging enabled for this rule. I was look...
Hello all, I have a simple question. I have 2 ASA 5510 in Active/Standby. Active INSIDE IP is 10.1.0.3, failover is 10.1.0.4. Due to an asymmetrical routing issue - I need to change the INSIDE IPs to 10.5.0.3 and 10.5.0.4 respectively. I have a...
we have two ASA in multicontext mode. When I connect to primary after few min it got disconnect when I try to login again it login to secondary device. 13:31:11 GMT/BDT May 9 2018Standby Ready Failed Interface check 13:31:24 GMT/BDT May 9 2018Fai...
Firepower 2110 supports Multi-WAN?
We had sold 2 IPS subscription licenses to our client for their two Cisco ASA Firepower modules. In return from Cisco, we received one software claim certificate containing the 1 PAK key. From its description, it is a Cisco ASA5515 Control License....
Dear, We have recently purchased two Firepower 2110 with threat, malware and URL license. Below is the BoQ of the new hardware Cisco Firepower 2110 Master BundleCisco Firepower 2110 ASA Appliance, 1USNTC-8X5XNBD Cisco Firepower 2110 ASA Appliance...
Hi,I'm rather new to the ASA box. recently I tried to use:asa#show ip route <dest_ip>which is not an asa command, ok. But show route does not accept parameter as an destination ip address. I have many outgoing interfaces (20 or so) which are only int...
Hi, I need to gain access of a ASA Context using ASDM. I am unable to configure ASDM image syntax (asdm image disk0:/asdm-xxx.bin). However the same syntax is valid when used on system context. Please advise how I can fix this. FW1/contex1(config)...
I configure ASA 5510 for Redundant ISP links as screenshot shown (Outside is primary and 4G-LTE is backup). However, when the Outside is down, the backup 4G-LTE doesn't work and on one can access the Internet. How can I troubleshoot it?
