Hello Cisco Community, I have a ASA 5506-x with a bunch of vlans (sub-interfaces) is there anyway to disable the security levels and purely use ACL's?
Hello Cisco Community, I have a ASA 5506-x with a bunch of vlans (sub-interfaces) is there anyway to disable the security levels and purely use ACL's?
Hi everyone, We are planning to buy additional control license to block application like Psiphon3.exe. Is it already possible to block that given application? I already read some thread that although there is category under vpn/proxy and the psiphon...
Hi Team, We have been asked to confirm if we can achieve the below using firepower solution (NGIPS or NGFW): Blocking of Whatsapp client on the end user machineBlocking of file uploads but allowing downloads from the drop box based sites on interne...
Hi Team, Is it possible for the NGIPS to understand the presence of application on end user system and then take decision of blocking the network communication of the same like for example the AV is not present then block the communication of that d...
Question on FireSIGHT / FirePOWER TA subscription license. Sensors come with perpetual Protect and Control licenses but require TA subscription for system updates. What is the extent of updates covered by TA license? Is it signatures only? Will Smar...
Hi all, i wanna configure my asa to get access to 2 VPN link the first via gateway 10.240.20.1 and the second via 10.240.30.1 but the ISP router use the intervlan routing in both interfaces i have just 10.240.20.1 but i can ping 10.240.30.1 via 10.24...
I have attempted to create ACL's that would allow me to simply ping from any inside interfaces to desktops outside.... but nothing is working. Any help would be greatly appreciated by looking at the below config and telling me if you see anything wro...
Hi All, Does anyone know of a command to clear the maximum conn counter on a Pix 501. Have had a look around the internet but can't seem to find a command that clears it? Really don't want to have to do a reboot! Thanks Shaun
Hello I should reach our ftp servers in LAN from a public server. For example our public server 2.2.2.2, public interface of asa is 3.3.3.3. I set the following: Object NAT: object network obj_10.20.2.2 nat (inside,outside) static interface service t...
Hi, How to configure summer-time daylight savings in FirePower Management Center? BR, Kiki
Hi, I didn't find any documentation how to restore a failed FTD, for example after a hardware RMA or a failed upgrade, as in my case. I've already reimaged the FTD and want to re-register it with the FMC. It's part of a failover pair too in our case.
Both icmp and icmp error inspection is disabled in FTD 6.2, was enabled in 6.1. This breaks e.g. ping through the FTD and isn't mentioned in the 6.2 release notes. Is this a new bug caused by the addition of FlexConfig or deliberately changed, becaus...
Hello, I have an NAT statement which is calling two pre-defined objects. Now I want to change attribute of the object. I need to know will it take immediate effect to the NAT statements or I need to delete and re-create the NAT statements. If NAT ...
before i was able to access my both ASA's ASDM with proxy setting in my PC. After i upgrade one ASA, can't able to access with proxy setting in PC? I'm still able to access other ASA via ASDM. Can any one know this ASDM access with proxy setting in ...
Dear All, My need is for our mailserver is below: Able to send and receive emails from - to outside internet domains with two public ip addresses from ISP1 and ISP2. Our Dns records for ourdomain.com are on the ISP1 and ISP2's Name Servers with the s...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2025 10:57 AM | ||
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM |
User | Count |
---|---|
10 | |
7 | |
5 | |
2 | |
1 |