Resolved! Defence Center - Do I Need It?
Do I need to run Defence Center to manage my FireSight 3d7050 devices? I only have 2 devices to manage but I don't see anywhere on the devices how to add policies or even view policies. Thanks Nick
Do I need to run Defence Center to manage my FireSight 3d7050 devices? I only have 2 devices to manage but I don't see anywhere on the devices how to add policies or even view policies. Thanks Nick
I am using a Cisco ASA 5510 which has 4 interfaces: Inside, Outside, Failover and the DMZ. The DMZ interface has two subinterfaces.The Inside interface is setup as a Physical trunk with a subinterface having a Vlan (example: Vlan 10)The Outside inter...
Hello Cisco Community, Guys, I need your support and comment about how stablish one Static Nat range port on the ASA 5520 IOS 8.2. Example: Private IP 10.1.1.1 ports 4000 - 4500 Public IP 200.100.10.1 ports 4000 - 4500 Regards and thanks!
Hi, i currently have a Cisco ASA 5545 in multimode running several contexts. I have the SFR module added into Defence Center but its not discovering all interfaces within a context. If i add another interface to another context that appears fine. So ...
I have bad port or cable on my ASA firewall. So i want to swap the port to rule out port is not the issue. so if i remove the config on the existing port then NAT and ACL associated with that interface will also be remove or not? that port is my outs...
Hi , I'm getting the following error while apply the Sourcefire_3D_Defense_Center_S3_Upgrade-6.0.0-1005.sh Update Installation Failed: [ 1%] Fatal error: Error running script 000_start/003_check_DC_memory.pl Any resolution will be appreciate Th...
Our ASA 5510 stopped working when we moved to a new building, we keep the same ISP and IP adresses. I can ping our router and ASA, but I cannot ping the ISP interface and gain access to the internet. We've tried several things attempting to get it to...
I have setup a ASA-5555-X in a lab in Multi-context mode, using the latest 9.5 code. There is an out-of-band management network connected to the MGMT port. I have 2 customers, each has their own security context. Problem: When you log into the ASA th...
Hi, we have a bit wide open Cisco ASA in term of ACL and we want to tighten it. but there are lots of LOGS generated by ASA and its hard to filter required information. What i need to achieve is Disable all logging for time being and only LOG a parti...
Dear All ,I used my Defense Center (version 5.4.1.3) today to upgrade 2 of our managed devices (sensors) from 5.3.0.7 to 5.4 but the upgrade failed on both devices at 7% with error "file integrity check failed" although one of them was upgraded yeste...
Hi all, I have ASA5520 8.4 INSIDE network (10.0.0.0/24) and DMZ network (webserver-->172.16.0.5). Webserver is static NAT with 116.x.x.146. When i access my webserver from INSIDE network to ip 116.x.x.145 no problem at all. But when i access my webse...
Hi Everyone, Here is a setup Server------ASA1----Switch1-----Switch2-----inside interface-ASA2----outside public IP where server1 ASA1 and Switch1 is new setup. Traffic from server needs to go to interent. Server subnet is 10.50.50.x ASA inside inter...
Hi All, I have the following on my ASA for VOIP QOS priority over a T-1 speed WAN: class-map QOS-IN match access-list qos_priority_in class-map QOS_OUT match access-list qos_priority_out policy-map QOS-POLICY class QOS-IN priority class QOS-OUT pri...
hello, i'm trying to setup basic firewall using cisco configuration professional after configuring router using terminal. After I run "create firewall wizard" and apply rules, inside clients cannot browse internet (from router I can ping outside). ...
Hi, I am trying to firstly upload the new asa951-smp-k8 firmware into the firewall flash so i can upgrade the ASA. My issue is that it fails before it can finish uploading into the flash. I have tried this via TFTP and via the current ASDM but it loo...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-06-2026 12:20 AM | ||
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM |
| User | Count |
|---|---|
| 2 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |