Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

I'm having trouble getting an FMCv managed HA Pair of 2120s ver. 7.3.1 configured for SNMPv3 monitoring via Auvik collector. The Auvik collector are not detecting SNMP as available. I'm using the devices>platform-settings>snmp as my setup per the doc...

razelle by Level 1
  • 838 Views
  • 3 replies
  • 0 Helpful votes

I'm in the process of adding more switches to support the FTD 3140 Cluster.  Here's the question, won't the Firepower devices go down if the switches that it's connected to also goes down?  Wouldn't that make the Switches (even more importantly, the ...

red2play by Level 1
  • 588 Views
  • 2 replies
  • 0 Helpful votes

Hi all, I issued the Failover Active on Standby ASA and No Failover Active on Active ASA but both ASA all cannot change the state. At the time after issuing this command, the SSH session on the ASA also drop and has to restart session again. The two ...

Hello,I've tried to look for a solution to this but can't find one for the defense orchestrator. Essentially the users are getting EDT time when viewing the monitoring page within the cloud fmc rather than local time, I know that on the full FMC it's...

sfs rel by Level 1
  • 1510 Views
  • 3 replies
  • 0 Helpful votes

I followed this YouTube video to create the instance. https://www.youtube.com/watch?v=_WfqPZWgM0c&t=1212sI pre-created four interfaces. The mgmt and diag interfaces are in the mgmt subnet that has a default route to IGW. The inside and outside interf...

Hi Team,We have FTDs monitoring with its Management Interface. But the monitoring tool doesn't fetch the details of FTD interfaces or any details of resources such as CPU, Memory etc. Not sure what needs to be done to get this info. We have only 4 OI...

ssan239 by Level 1
  • 486 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Cisco ASA NAT

hi i have an issue with nat i need to solve i have two servers that they are natted to two public IPs let say 192.168.1.1 to 1.1.1.1 192.168.1.2 to 1.1.1.2 i want them they can connect to each other by public IPs when 192.168.1.1 pings to 1.1.1.2 the...

Hi All,I've been tasked with migrating DMZ from a legacy ASA to a FMC managed FTD.Currently there's a transit LAN to route DMZ destined traffic to the ASA.We have a 20G (2x10g) port-channel between the core switch and the FTD and all zones listed bel...

atsukane_0-1693988082147.png atsukane_1-1693988109423.png
atsukane by Level 3
  • 1340 Views
  • 9 replies
  • 0 Helpful votes

Hell All, I am using ASA 5500 in my office and would like to open few ports, imap.gmail.com, 993 and smtp.gmail.com 465, 587 for gmail. Can someone help me to create and ACL for the same. Since gmail IP's changes very often, I am confused. Appreci...

HiI would like to configure inter-vlan routing in firepower(FMC) using VLAN sub interface.I've created sub interfaces with separate VLAN ID on physical interface. And I've configure trunking port at the access switch side with appropriate gateway.But...

SaintEvn by Level 1
  • 16247 Views
  • 17 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card