Hello Expert,I have ASA5510. It's include security plus license.I want to traffic shape to 200Mbps. But , I checked a CCO.CCO said that a shaping limit is 154400000. "Enables traffic shaping, where the average rate argument sets the average ra...
Hello Expert,I have ASA5510. It's include security plus license.I want to traffic shape to 200Mbps. But , I checked a CCO.CCO said that a shaping limit is 154400000. "Enables traffic shaping, where the average rate argument sets the average ra...
Hi Experts,I have a problem on allowing ssh traffic between 2 different INTERNAL interfaces. Both the interfaces have the same security level (100).What I have to do is to allow a ssh command from 172.16.0.2 to 172.17.1.200. The firewall is configure...
Hi experts,I am installing an ASA 5520 and I have a problem on accepring the incoming traffic from an external office connected via Frame Relay.On my OUTSIDE interface I have both the internet traffic and the external office traffic incoming. What co...
HelloI have two interfaces connected to two different subnet - interface 0/1 = 10.100.1.0/24 , interface0/2 = 10.100.113.0/24 as they are direct connected to the ASA i assume i dont need to add an static route but when i try to pi...
Hi,I'm trying to publish my Lync, and for that I've created a NAT rule and an Access rule that redirects an external IP to a DMZ IP, but it did not worked, so I started to dig what was the problem, and then I figured the external IP I am using was th...
I am unable to ping my computer (attached via crossover). I can ping from the PC, but not from the PIX515. I'm using ethernet 1, and I have its IP set at 192.168.1.2/24, but for what ever reason I am unable to contact the computer. I tried messing wi...
i have a unique thing to do i have been given a task of connecting a WLC5508 to a ASA5510 because the dont want to get a another switch.how can i do this. i think it is possable to do but i cant get the NAT and ACL to work right.here is what i have s...
I have an inside network using PAT to one outside address. Our DNS server is on anotherlocal, but outside address. I can't get the inside network to successfully get addresses.I have another inside address that just uses the wirewall and gets addres...
Good Morning,I am fairly new to configuring ASA's so I wonder if anyone could help with an issue I am having. I have an ASA 5505 with one outside interface and three inside interfaces (inside1, inside2, and management). I need inside1 and inside2 to ...
Hi,We have ASA 5520 with currently code 7.2 running on it with 512 MB default memory. If we need to upgrade the code to 8.0 or 8.2 is this default RAM of 512 MB sufficient to run the new 8.0 or 8.2 code?Or do should upgrade to 2 GB upgrade kit is it ...
Hi all, I lake many others am having trouble with a web server in a DMZ. I can't hit it from the public side and I can't hit the public from the DMZ web server machine. My SMTP and HTTPS to a different machine work flawlessly. Could some please p...
can anyone tell me why my dns requests on cbac are not working, I allowed everything from inside out, but dns requests are not allowed for some reasons...Building configuration...Current configuration : 3265 bytes!! Last configuration change at 08:47...
Hello and thank you in advanceI have a ipsec tunnel setup with the use of object groups. This ipsec tunnel is active and in production. If I need to add one more IP to that object group will I need to do anything for it to take effect or that will b...
I'm hoping someone can assist...I've been having a major problem with our Internet service. Our ISP insists it's the firewall.I'm not a Pix expert by any means, but here's what's happening:- Our Internet service drops.- When this happens I try to pi...
Hi all,Over the last couple days I've been experimenting with the new NAT config with version 8.4(2), and I've got a couple questions.For example:My production ASA is running on version 8.2(3) and has the following config:global (outside) 1 interface...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM |