Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi All,Just want to know if there is a way to configure secondary IP address on the outside/public interface of ASA/PIX.One of our clients have used most of their IP on the subnet given by their ISP. They use those IP's for staticallymapping to Serve...

oyd110380 by Community Member
  • 3297 Views
  • 3 replies
  • 0 Helpful votes

i have a 192.168.1.0/24 address behind the firewall of an ASA. they only want to translate the half of the /24 address as a routable ip, the rest of the addresses (/25) will not be translated.Would this work as below?global (outside) 1 interfacenat (...

kope by Level 3
  • 631 Views
  • 1 replies
  • 0 Helpful votes

I have 3 Servers in my DMZ.  The Servers can VNC and ping each other fine.  From 'inside' I can ping and VNC 2 of them, but not the third.  From 'inside' I can access NS2 (172.168.1.12) and WebServer (192.168.1.10)I cannot access NS1 (172.168.1.11)  ...

Lon by Community Member
  • 2412 Views
  • 6 replies
  • 0 Helpful votes

  Dear experts,    rtr 1                       rtr 2          .1                         .2       |                            |       |  10.10.10.0/24      |       |                            |                                  ASA_active      ASA _...

kope by Level 3
  • 11747 Views
  • 8 replies
  • 0 Helpful votes

Hello everybody.I am managing a firewall setup with some ASA 5510's.One of the rules I have in the ACL list is to allow or deny (By disabling the rule) access to certain subnets.I have a 3rd party vendor that from time to time need access to specific...

Hi,This may be a stupid question, but if I have an active/passive pair how do I connect to the passive box? I need to upload a any connect image.Sent from Cisco Technical Support iPad App

Kris Wolton by Community Member
  • 1268 Views
  • 3 replies
  • 0 Helpful votes

Hey all.Looks like at some point a Cisco TAC member added, "same-security-traffic permit intra-interface" to my config.  Since I have a base license, I only have 3 vlans (2 1/2 really): inside, outside and dmz, which are on security levels 100, 0, an...

newmindeye by Community Member
  • 1818 Views
  • 4 replies
  • 0 Helpful votes

HelloI'm trying to configure an asa 5510 using this config : enable password XXXXXvpdn group PT request dialout pppoevpdn group PT localname ISPUsernamevpdn group PT ppp authentication PAPvpdn username ISPUsername password ISPPassworddhcpd auto_confi...

kazaam1983 by Community Member
  • 1599 Views
  • 5 replies
  • 0 Helpful votes

Hello All,       I have a Comcast Business as my internet service at home. I am getting 50 megs downloads behind my Comcast modem however behind the firewall I am getting 10 to 12 megs. All my firewall ports are hardset to Speed 100 and Duplex full. ...

I am trying to open a port to get to a camera that is located behind the asa 5505.  I have looked thru the discussions and most of the guides I have found are for 8.3 and 8.4, I however have 8.2 on this device and after a full day banging my head wit...

slankyco1 by Community Member
  • 3903 Views
  • 5 replies
  • 0 Helpful votes
Top Solution Authors
Review Cisco Networking for a $25 gift card