I have one ASA 5520 up and runnign, with complete configuration (ssl customization, DAP, CSD...) with bunch of files on flash drive, etc. I am using software 8.3Now I received one 5520 that I want to use failover, it is with 8.3, I will make sure tha...
alright folks, i'm new with the asa's...i'm familiar with the FWSM's on 6500's and pix...I'm running Version 8.3(2) and i wanted to setup nat-control and use of identify nats for advertising inside subnets to my outside networks.the old command was s...
Hello,Is it possible to manage (via the ASDM) my ASA from a *inside* LAN to the *outside* interface? I know this might sound crazy but believe me, I have good reasons.Just to show you: inside if ...
Hello Friends,I have applied a static Nat for 1 of the server in DMZ interface , I have done proper static Nat and also given for port 80 traffic on outside access list,The strange thing is when i do capture on my outside interface for public IP i r...
Hi,can anyone guide me to configure ASA 5510 as belowinside users should communicate with Hosts on the DMZ Zone and at the same time they should go for internet towards outside interfaceASA with 8.3(1)default security levelsattached is the digram for...
hi all,i two 5550 firewall set up for redundance purpose . in failover we define two different ip add one for primary and one for secondary .exampleinterface Ethernet0/0 nameif outside security-level 0 ip address xxxx.0.0.0.1 255.255.255.0 standb...
Just wanted to know if someone could show me step-by-step how to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely. Thank you.Thomas
Hi everyone,I hope this is an easy one for all. I have a router on a stick setup going on and I would like to put a firewall into the picture. I have two VLANs - VLAN 2 and VLAN 3. VLAN 2 is in the 192.168.2.x network and trunks back to the router at...
I currently have an ASA 5510 unit. I have a dmz setup which house some web servers and an inside interface. The web servers contain multiple public ip addresses which I have natted and access is fine.What is the most simple way to enable ping for my ...
Hi all,I have a central site with few remotes sites connected this way: 1) A pair of Cisco ASA 5520 deployed in ACTIVE/PASSIVE redundancy at the edge of all sites including the central 2) ALL sites are interconnected by VSAT via the central...
Hi,We are using Websense as Proxy. The Signature 6009/0 & 5930/8 triggers (SYN FLOOD DOS & GENERIC SQL INJECTION) triggers and blocks Internet traffic comming through proxy. Times the Signature changes and its very difficult to know root cause.In the...
Hi,Is it possible to establish PBR rules that set the ip next-hop to point directly to the inside interface of the ASA5550?Or, do I need to direct this PBR traffic first to a directly connected router interface and then default route to the ASA?At a ...
Hi,I've recently purchased an SSM-10 and it has come with v6.0(6)E4When trying to upgrade to the latest version, I am getting the following error:Cannot Upgrade Software on the SensorerrSystemError-IdsPackageMgr: digital signature of the signature fi...
Is this the correct part no. for the IPS 4240 Sig Update License? CON-SUSA-IPS4240SI can only find this part number in the ordering tool: CON-SUI-IPS4240 which also has SMARTNet Support?Which one do we need just for having Sig Updates?Thanks
Dear Support-Team,I have ASA 5510.Is there any difference between CSC-10-PLUS license and Security Plus License...Regards,Janardhan
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-24-2026 10:39 AM | ||
| 06-24-2026 08:00 AM | ||
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM |
| User | Count |
|---|---|
| 5 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
