Has anyone experienced problems changing the logging severity level of a Syslog ID to either raise or lower its level within the ASDM? I want to log certain activities that are currently set as notification and informational but don't want to log ev...
Hello,I upgraded from 4.5.1 to 4.7.1. I am having trouble with the communication between the CAS and the CAMHere is an outline of the issue1. After Authentication, DHCP, ACS ok, WALL !!!2. Nac Online Users = 03. Ping the CAM HA serv...
I am trying to setup a second vpngroup on a pix 6.2 (I knowit is old but can't upgrade it yet) and am having a problem. I can connect to the new vpngroup and it works when there is not split tunnel configured butwhen I add the split tunnel command it...
Hi allWe use 2 FWSM version 3.2 (4) in active-failover, transparent, multicontext mode.I have now a problem with backuptraffic (TCP) between an application server and a backup server through firewallthat traffic hangs after 1,5 hours. In the sniffert...
Is it possible to have Multiple Internet Gateways on a ASA5510?? I would like to route some traffic out on one outside interface and the rest out the other. As of now, ISP1 is the default gatway.
Hi friends..What are the steps to upgrade ASA 5510 to Security Appliance 7.2(1) with ASDM 5.2.1?Thanks a lot!
I have a Cisco ASA 5510 with the CSC-SSM module installed. Is there a way to configure the CSC-SSM to block web sites but also allow specific users access to these sites?
Hi all,I try to analyze a complex PIX config and would like to analyze the NAT usage. There are ALL variations of NATing in it, therefore I get static, dynamic, nat exemption etc.I can see how I could trace down dynamic NAT (by counting "built dynami...
dearsi have a aproblem with connection between ASA 5510 and WASS , after i am check another ASA 5520 that Support inspect WASS ,but i want to allow inspect WASS on ASA 5510 , so how can i solve this issue plzRegardsAlaa Jararha
Hi All,I'm trying to figure out a problem on a 5505.I've created a static mapping and adjusted the acl on the outside interface to accept traffic for the public ip address in the mapping.When I run the packet-tracer to verify if traffic is allowed to...
Hello All,I'm having hard time with our NGS. It was using the 2.0.0 version but only tha start- end type time profiles were working with that version. We decided to upgrade to version 2.0.1.Now we have the other types of the time profiles and they ar...
We have two ASA5520's in a active/standby configuration. We have been unable to use any of the show commands. Everything else seems to work ok but if we want to look at the running-config/startup/interfaces etc, anything that uses show, it just sits ...
Dear Folks,Recently we had purchase, NAC Manager, Nac Server, Nac VPN and Nac Profiler. If any one can provide a little push in right direction, to Implement right scenario in an Enterprise Network for Remote access VPN, through SSL VPN on ASAMuch Ap...
Hello everyone, I am configuring a PIX 501 for a small office situation, and have a server internally that is providing web-based services on two separate ports. What I want to do is map a public IP for each internal service on the same server. Th...
I'm setting up an anyconnect vpn connection. I see that I need to createa ssl key for this. It uses the same command to generate an ssh key.Will the newly generated key replace the existing key? If it does is there any impact outside of the ssh keys ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 9 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
