when the aip ssm module is in inline mode. does the packet first is scanned by the aip ssm module or it is first checked by the firewall rules whether it is permitted and then sent to aip ssm module. can someone throw some light on this. regardssushi...
Hi all i am trying to figure out the load-balancing between 2 idsm2 modules in the same chassis. this is the config i am trying to dorouter(config)# intrusion-detection module 6 data-port 1 port-channel 5 (idsm1)router(config)# intrusion-detection mo...
We have a client with a Cisco 871 router and we want to setup users with the ability to use the Cisco VPN client software and conenct to the office 871 router to gain access to resources behind the 871.Could someone please give me a few tips or steap...
Hello,I have 30 locations hub and spoke off from an mpls network. There is also a DSL vpn backup to each location. Both MPLS and VPN terminate into a 2811 onsite at the remote branches. We are using IPsec VPN Tunnels. We are using eigrp as a routing ...
What is the reference of the item needed to enable asa failover ?
Have I missed the obvious? I want to record the configuration of my CAM/CAS in a human-readable format. All I can think of is screen shots, but these don't show the full character string in a scrolling text box, and also after 40 screen shots I still...
Dear All,I would like to ask you some question that i have the problem, so i cannot sovle.i was configure VPN client on ASA. and the VPN client now it is working and and can ping to LAN HQ.and my problem can not ping 40.40.40.1 other lan.Pleaes kindl...
HelloI have tunnel s2s via ipsec. On my asa i have inside and outside interface. My LAN are 192.168.10.x, Remote LAN 192.168.20.x I try to debug problems with connection which comes, initialized from remote site to my ASA. When ipsec packet arrives t...
Hello, I have NAC configured to run some Nessus scans but I keep coming up with this for any application-specific ones... Please advise on what I'm missing. I don't know what this means.[Thu May 21 14:25:30 2009][7152] user perfigo : Not launching qu...
Hello,I'm looking for elegant solution to migrate VPN Clients to new public IP.I have PIXs (public IP x.x.x.1) and Concentrator (x.x.x.2) to be replaced with ASA. All VPN Clients (~200 users) preconfigured with x.x.x.2. What is the best way (minimum ...
I have seen postings, and heard of cases where people actually assign public IPs to servers sitting in a DMZ behind a firewall. My question is, if you only have one IP block(say a /29), how can you do this? I understand if you either 1-1 NAT or PAT f...
Hi All,I am using DHCP in my network. And i need to reserve one IP for the Management Interface of the IPS.I tried to get the MAC but couldn't. It is not even on the Show tech-support.Can any please tell me how to get the MAC of Management interface ...
Hi,I have a cisco PIX 501 in which remote VPN is configured for our company. Currently, for the remote users, the authentication is just a vpn groupname and a password. All the users use the same credentials for logging in. Can I have separate remote...
I have a web proxy ..tunnel filters...and AIP-SSM....inside of the network...i configure host service, network setting and hhtp-proxy to use my proxy when updating global corelation ...On proxy I allow hhtps to 204.15.82.17 ---ironport service. In pr...
I have a 4215 which needs to be upgraded to 6.x code. current config: Cisco Systems Intrusion Detection Sensor, Version 4.1(4)S91OS Version 2.4.18-5smpbigphys-4215Platform: IDS-4215is there white-page for upgrading from this low of code level?thanks,...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-24-2026 02:14 AM | ||
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
