Dear all,Please advice in one thing. Imagine I am looking for user which is causing most of the connections over my firewall.On ASA I was using simple commands (where 500 is number of connections per ip address):sh local-host connection udp 500 | i l...
Forum Posts
This is my first time posting here, so bear with me.Our company runs ASA5545X with Firepower in each of our 2 data centers. For the last 2 years, we have been having an ongoing issue where they stop passing traffic. In the last couple months, it has ...
Hi Expert,I'd like to modify order of accessrules via API.I explored api/api-explorer, however could not find related fields like sequence number.I also couldn't find fields regarding Category.Could you please let me know they are available?Thank you...
Resolved! Cisco ASA Multi context AWS VPN
A client of mine has a Cisco ASA that's currently running on multi context mode and needs to configure a site to site VPN to his AWS VPC. Kindly advise how to go about this as VTI is not supported on ASA in multi context mode.
Resolved! Cisco ASA 5506 Firepower
I am confused as to whether my ASA 5506 units have firepower or not. Reading through forums so far, I gathered that firepower is not really supported on the ASA 5506 on versions 9.10 and up. Both of my ASA 5506 are running 9.14. A couple of show out...
Hi,I have Firepower 2100 (Cisco Fire Linux OS v6.2.3 (build 13) Cisco Firepower 2110 Threat Defense v6.2.3 (build 83))and my pc have IP is range: 172.31.31.xSSH (IP: 172.31.31.254) is ok, , unable to access https, and unable to add management IPv4, w...
I'm setting up a FPR1140 FTD 6.7, which is managed with on box Firepower Device Manager, for BGP routing. However I can't seem to find a way to configure "soft neighbor reset". The classic soft-reconfiguration inbound command does not seem to be supp...
How does one go about doing threat analysis within FMC? As you can see from the attachment the dashboard lists threats. I am extremely weak at this part of Firepower and have not a clue how to go about an analysis workflow here. What would you guys d...
Resolved! add FPR4112 to FMC and show me error
Hello , I have a problem . I have FMC 4600 and i want to add two FPR 4112 to FMC but i can't !!! i have two switch layer 3 have a protcole HSRP and with configuration : we are VLAN 254 and interface Vlan254Edge-To-LAN# ip address 192.168.254.251 25...
Greeting allI can't find a method to Delete/Cancel or Retract tickets 'ready to deploy' within CSMI can purge the tickets through the Security Manager Administration, however this is a drastic measure as this procedure, purges all tickets for all use...
Resolved! routing Issue [ FTD ]
Hi all , I've added more subinterfaces over the FTD and set policy [ ANY >> ANY ], but the connection between these subnets is down. FMC version : 7.0.0 Find the attached files to check the Configuration
Is there a command to add a vlan to only unused ports on switch. We have existing production switches but we would like to add a unused vlan to all unused ports. I know the range command, but there are many active ports on the switch and wanted to...
Resolved! ASA 5525 ACL traffic behavior...
Hello.I am unclear on ASA 5525 ACL traffic behavior...If an ACL is implemented on an interface in one direction, are packets within this session that have been permitted by that ACL automatically allowed back in from the other side during that same s...
Hello,i've installed two Firepower 1140 in ha running 6.6.5.2-14 version and they are managed via FDM. I'm receiving this errors when trying to query them via SNMPv3: %Received a report pdu from remote host: Unsupported SecurityLevel (SNMPv3) the con...
Hi,Recently we deployed cisco firepower FMC and FTD and monitoring it via SolarWinds. We are unable to get the serial numbers on SolarWinds tool. When we list resources, we don't see hardware sensors. Please suggest what IODs are used for hardware se...
