Need instructions on how to return to v602 after an upgrade to v611 was performed.The recovery partition is also at v611.
Need instructions on how to return to v602 after an upgrade to v611 was performed.The recovery partition is also at v611.
I am having difficulty connecting to the console port on a new out of the box cisco 1113 Secure Access Control Server. When connected I don't see anything on the screen (no login prompt etc). I have used hyper-terminal as well as putty with no luck...
Hello,I have two documents for password recovery on the 4235. Can you advise which one to use? The first one listed below seems easier but I have a feeling I'm missing something. Thanks. http://www.cisco.com/en/US/docs/security/ips/6.0/release/notes/...
I'm running into an issue where my 6509 with FWSM installed is lets www requests through, but blocks DNS, despite being told to permit both.Most perversely, it's blocking DNS on my internal networks. I've got the FWSM set up in single context mode, w...
Hi,I'm pretty sure I've seen a solution to this problem before but I just can't seem to find it...I have LAN users trying to access servers in the DMZ via their public IP's. They go out the outside interface to do this but are getting dropped as spo...
Hello,I have make a IPSEC VPN between ASA 5500 and another Firewall NETASQ. The tunnel negociate successfully but all the traffic betwenn the local and remote net work fail. When I ping local host from remote host I get "no translation group error".I...
We recently purchased two Cisco compatible 512 MB flash drives for our ASA. The drives work fine when first inserted into the ASA. We are able to load boot images, ASDM, CSD on the flash cards. However, when we change to boot statement to boot off...
Hi Gurus, Appreciate if you can help me on how to configure ip telephony. My configuration is PBX-router-PIX-router-PBX. Any documents or sample configuration on my PIX would be great.Thanks so much,Jong
Hi,I have a question regarding operation steps on IPS on ASA - while configuring access list for interesting traffic, do I need to use really or NATed addresses. Precisely, NAT and than access list or access list and than NAT?
Hi all,Friends, I have ASA 5520 with CSC SSM module. i'm configuring this module but it can not be updated. My pc could reach internet with no problem. PC and SSM module has the same gateway and both are in the same subnet. When i connected and using...
Why I am not able to give vlan commands on my ASA5510 (security plus license? ciscoasa(config)# interface vlan 50 ^ERROR: % Invalid input detected at '^' marker.ciscoasa(config)#
HiI have a problem... when I try to permit in a temporary role a web page (for example www.microsoft.com) the user can't open it and display security message but when i add the web ip the users can access.... the nac is working on real-ip layer 3...t...
When using no nat control on a FWSM, I would assume that the xlate table (sh xlate) should be empty.Is this correct as I am seeing some one to one entries in the xlate. I am not seeing every single host, only approx 200 out of 5000 potential hosts.Ca...
HI, Installed ASA 5505, want to connet linux machine over internet to ASA 5505 vpn.Does ASA 5505 supports linux vpn client ?Pls. guide
HiI have 2 pairs of ASA5520's one pair at my Head Office the other pair at my DR site. they are configured as Active Standby Pairs at each site with a vpn tunnel between the two sites.I have traffic that originates off one of the interfaces on the AS...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM | ||
06-11-2025 07:59 AM | ||
06-11-2025 06:59 AM |
User | Count |
---|---|
5 | |
5 | |
1 | |
1 | |
1 |